ZCG0060C Datasheet, PDF (4/4 Pages) Red Lion Controls. Inc – MODEL ZCG - SINGLE CHANNEL OUTPUT ROTARY PULSE GENERATOR

MODEL LSAHC - LENGTH SENSOR HINGE CLAMP ASSEMBLY
The Length Sensor Hinge Clamp Assembly provides an easy method for
attachment and mounting of the Length Sensors and LSCB1 Conversion
Bracket. The removable top on the solid zinc LSAHC mounting block
allows quick installation of the Length Sensor handle tube and provides
secure clamping retention. The mounting block pivots freely in zinc right
angle brackets to allow mounting the assembly via clearance holes for 1/4"
dia. bolts.
The lock washers must be used as indicated (between the bolt head and
the top clamp piece). Assemble the top clamp piece as follows.
1. Tighten both bolts so that the top clamp half draws down evenly on
the sensor tube.
2. Tighten the bolts until both lock washers are flat.
3. Then turn each bolt an additional ½ to ¾ turn.
DIMENSIONS In inches (mm)
FRONT
VIEW
2.5 (63.5)
1.25
(31.8)
Lock washers (2) must be
installed between bolt heads
and top clamp piece.
.25 (6.3)
.85
(21.6)
SINGLE WHEEL
2.93 (74.4)
DUAL WHEEL 4 (101.6)
Model ZGG Shown
CAUTION: Downward tension
on signal cable can cause
wheel(s) to lift. Make sure
cable is clamped to
machine frame near
encoder and allow slack.
NOTE: The weight at the
Length Sensor unit
provides sufficient traction
for accurate operation
when mounted as shown,
with arm angle from
horizontal not exceeding
±30°, and with hinge clamp
toward the far extreme of
the extension arm.
3.4
(86.4)
2.9
(73.7)
TOP
VIEW
2.00
(50.8)
1.50
(38.1)
0.75
(19.0)
4X Ø 0.31 (7.9)
0.75 (19.0)
E-clip retaining ring (2)
must be installed in slots.
.88
(22.4)
WRHAEDEIULS
6.9 ^(175.3)
(14.98.3)
.88 (22.4)
4.50 (114.3)
5.70 (144.8)
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
LSAHC Length Sensor Hinge Clamp Assembly
PART NUMBER
LSAHC001
Model ZFG Shown
Length Sensors should be mounted so measuring
wheel(s) contact ribbon, strip or web as it passes over
a roller. As an alternative, wheel(s) can be driven by
roller surface next to material being measured.
Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained
herein and relies on no other warranties or affirmations.
Red Lion Controls
Europe
Printerweg 10
NL - 3821 AD Amersfoort
Tel [phone]
Fax [phone]
Red Lion Controls
India
54, Vishvas Tenement
GST Road, New Ranip,
Ahmedabad-382480 Gujarat, India
Tel [phone]
Fax [phone]
Red Lion Controls
China
Unit 101, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel [phone]
Fax [phone]