G3HSPA00 Datasheet, PDF (2/4 Pages) Red Lion Controls. Inc – MODEL G3HSPA - G3 SERIES HSPA+ CELLULAR MODEM OPTION CARD FOR G3 OPERATOR INTERFACE TERMINALS

3. COMMUNICATIONS:
Isolation from G3HSPA Antenna connector to G3 operator interface:
500 VDC for 1 minute.
4. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: 0 to 50 °C
Storage Temperature Range: -20 to 80 °C
Operating and Storage Humidity: 80% maximum relative humidity (non-
condensing) from 0 to 50 °C.
Altitude: Up to 2000 meters.
5. ANTENNA CONNECTOR:
SMA Female connector requires:
50 Ohm antenna with SMA male connector
Penta-band HSPA+ antenna (850/900/1700/1900/2100 MHz) for global
support.
Dual-band (850/1900 MHz) antenna for US and Canada only
Dual band (900/2100 MHz) for Europe only
Voltage Standing Wave Ratio (VSWR) should not exceed 2.0:1
The antenna cable should be 50Ω impedance, RG178/U or RG174/U type and
be able to connect to the RSMA (Male) jack bulkhead. The antenna could be
horizontal, vertical or right angled. Longer antenna cable would equate to
signal loss.
6. CERTIFICATIONS AND COMPLIANCES:
SAFETY:
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment for
measurement, control and laboratory use, Part 1.
ELECTROMAGNETIC COMPATIBILITY
Emissions and Immunity to EN 61326: Electrical Equipment for Measurement,
Control and Laboratory use.
Immunity to Industrial Locations: Reference G3 unit for immunity
specifications
Emissions:
Emissions
EN 55011
Class A
Note:
1. G303 unit’s emission level changes from Class B to Class A levels when
G3HSPA option card is installed.
2. The G3HSPA option card has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC rules.
7. CONSTRUCTION: Installation Category I, Pollution Degree 2.
8. INSTALLATION REQUIREMENTS: Card must be installed inside the
rear cover of a G3 operator interface with the hardware provided. See
“Installing the G3HSPA Option Card” for more details.
9. WEIGHT: 2.5 oz (70.9 g)
Installing the G3HSPA Option Card
INSTALLATION INSTRUCTIONS
Caution: The option and main circuit boards contain static
sensitive components. Before handling the cards, discharge
static charges from your body by touching a grounded bare
metal object. Ideally, handle the cards at a static controlled clean
workstation. Also, handle the cards by the edges only. Dirt, oil,
or other contaminants that may contact the card can adversely
affect circuit operation.
Warning: Depending upon the G3 operator interface, high voltage
may be present inside the operator interface. Be sure to remove
all power before removing the rear cover of the operator interface.
Each G3HSPA option card comes with a cable for communications from the
main G3 operator interface PC board. It also comes with three screws for
attaching the option card to the inside of the G3 operator interface’s rear cover.
The first step is to buy a SIM Card from one of the GSM/HSPA+ providers
and insert into the option card SIM Card slot. The SIM Card slot is the
rectangular slot on top of the HSPA Cellular Modem in G3HSPA option card as
shown in Figure 1. See SIM Card details in the Software/Unit Operation section
for more details.
TOP SIDE
To install the option card remove all
power and communication cables from
the unit. The chassis ground
connection to the rear cover may
be left connected. The G3
operator interface literature
contains instructions for
removing the rear cover, refer
to the “Battery & Time
Keeping” section.
Using the three
screws provided,
connect the option
card to the rear cover
as shown in Figure 2.
V2 HMIs connect at
the main board.
Figure 2
Connect the cable from the option card to CN11 on the main board of the G3
operator interface as shown in Figure 3. Be sure both ends of the cables are
firmly seated into their appropriate connector housing.
HSPA CELL MODEM
G3HSPA00
OPTION CARD
SIM CARD
ORIENTATION
POWER
LED
ANTENNA
Figure 1
Figure 3
2