 English |
|
|
|
|
|
|
|
| PXU20030 Datasheet, PDF (16/32 Pages) Red Lion Controls. Inc – MODEL PXU - TEMPERATURE/PROCESS CONTROLLERS | |||
| |||
| ◁ |
7.3 MODULE 3 - Lockout Parameters (3-LC)
3-LC
PARAMETER MENU
P
CNFP
P
SP
SETPOINT
OP1
OUTPUT 1
POWER
OP2 SPrP PId r-S OPOF
OUTPUT 2
POWER
SETPOINT
RAMP RATE
PID
CONTROLLER
GROUP
STATUS
OUTPUT
POWER
OFFSET
ProP Intt dErt dInt
PROPORTIONAL INTEGRAL DERIVATIVE INTEGRATION
BAND
TIME
TIME
DEFAULT
AL-1 AL-2
ALARM 1
VALUE
Programming/model dependent.
ALARM 2
VALUE
AL-3
ALARM 3
VALUE
ALrS
ALARM
RESET
SPSL tUNE
SETPOINT AUTO-TUNE
SELECT
START
CtrL
CONTROL
MODE
trnF dEv
CONTROL
MODE
TRANSFER
DEVIATION
VALUE
CodE
ACCESS
CODE
SELECTION
ï¤ïïï
PArA
ïïï¤ï
ïïï
ï¤ïïï²
DESCRIPTION
Display: accessible in Display Loop.
Parameter: accessible in Parameter Loop
Hide: accessible in Hidden Loop.
Locked: not accessible in loops.
Display/read: read only in Display Loop, but read/write
in Hidden Loop.
The following parameters can be configured for the selections described
above. See Programming Loops section for a description of loops and
parameters.
PARAMETER
SELECTION
FACTORY
SETTING
SP
dISP, PArR, HIdE, LOC, dSPr dISP
OP1 dISP, PArR, HIdE, LOC, dSPr PArR
OP2 dISP, PArR, HIdE, LOC, dSPr PArR
SPrP dISP, PArR, HIdE, LOC, dSPr PArR
PId dISP, PArR, HIdE, LOC, dSPr PArR
r-S dISP, PArR, HIdE, LOC, dSPr dISP
OPOF PArR, HIdE, LOC
PArR
ProP PArR, HIdE, LOC
PArR
Intt PArR, HIdE, LOC
PArR
dErt PArR, HIdE, LOC
PArR
dInt PArR, HIdE, LOC
LOC
AL-1 PArR, HIdE, LOC
PArR
AL-2 PArR, HIdE, LOC
PArR
AL-3 PArR, HIdE, LOC
PArR
ALrS PArR, HIdE, LOC
PArR
SPSL PArR, HIdE, LOC
PArR
tUNE HIdE, LOC
HIdE
CtrL HIdE, LOC
HIdE
trnf HIdE, LOC
HIdE
dEv dISP, LOC
dISP
Parameters may not appear in selected loop if not applicable to current
operating mode.
Ex. 1. If Act2 = NONE, AL-2 will not be displayed in selected loop.
2. If CtrL = ONOF, PID parameters will not be displayed in selected loop.
ïï¯ï¤ï
ï
ïï°
ACCESS CODE
ïï±ï²ïµ to 125
ï°
Full access to Display, Hidden, and
Configuration Loops
ïï±
to
ïï±ï²ïµ
Code necessary to access
Configuration Loop only. *
ï± to ï±ï²ïµ
Code necessary to access Hidden
and Configuration Loops. *
* If PLOC is active, Configuration Loop is not accessible.
Shaded parameters are programming/model dependent.
16
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese