RP100-481.8S Datasheet, PDF (1/6 Pages) Recom International Power – 100 Watt Isolated Single & Dual Output

Features
● Single Output up to 25A
Dual Outputs Total Power up to 100W
● Input/Output 1.6kVDC Isolation
● Adjustable Output Voltage
● Under-Voltage Lockout
● No Minimum Load
● Industry Standard Footprint
● Fixed Operating Frequency
● Halt Tested
● Compact 61.0 x 57.91 x 12.7mm Package
● High Efficiency to 90%
INNOLINE
DC/DC-Converter
RP100-S_DI
Series
Selection Guide
Part
Number
Single Output
Input
Voltage
(VDC)
RP100-481.8S 36 – 75
RP100-482.5S 36 – 75
RP100-483.3S 36 – 75
RP100-4805S 36 – 75
RP100-4815S 36 – 75
Output
Voltage
(VDC)
1.8
2.5
3.3
5
15
Output
Current
(A)
25
25
25
20
6.66
Line
Load
Input Efficiency
Regulation Regulation Current⁽⁸⁾
(9)
(mV)
(mV)
(A)
%
4
6
1.157
86
5
8
1.608
87
7
10
2.022
90
10
15
2.480
90
30
45
2.507
90
Part
Number
Dual Output
RP100-483.305DI
RP100-482.505DI
RP100-482.53.3DI
Input
Voltage
(VDC)
36 – 75
36 – 75
36 – 75
Output
Voltage
V1 / V2
(VDC)
5 / 3.3
5 / 2.5
3.3 / 2.5
Output
Current
I1 / I2
(A)
Line
Regulation
V1 / V2
(mV)
Load
Regulation
V1 / V2
(mV)
Input Efficiency
Current^{(8) (9)}
(A) %
20 / 25 25 / 16.5 25 / 16.5 2.39 87
20 / 25 25 / 12.5 25 / 12.5 2.45 85
25 / 25 16.5 / 12.5 16.5 / 12.5 2.44 85
100 Watt
Isolated
Single &
Dual Output
Notes:
1. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used,
the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connected
to its corresponding -Vout.
2. Single: Measured with a 1uF M/C and a 10uF T/C.
Dual: For each outputs.
3. An external filter capacitor is required for normal operation.
The capacitor should be capable of handing 1A ripple current for 48V models.
RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90mΩ.
4. Single: The negative / positive logic and length are optional ( see table ).
The pin voltage is referenced to negative input.
Dual: The ON/OFF control function. There are positive logic ( standard ) and negative logic ( option ).
The pin voltage is referenced to negative input.
To order negative logic ON/OFF control add the suffix-N. ( Ex:RP100-483.305I/N )
5. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40°C.
( Ground fixed and controlled environment )
6. Heat sink is optional and P/N: 7G-0021, 7G-0022, 7G-0023, 7G-0024.
7. The RP100 meets level A and level B conducted emissions only with external components connected before
the input pin to the converter.
8. Maximum value at nominal input voltage and full load.
9. Typical value at nominal input voltage and full load.
The dual efficiency test condition: RP100-483.305DI @ 5V/12A and 3.3V/12A
RP100-482.505DI @ 5V/12A and 2.5V/16A
RP100-482.53.3DI @ 3.3V/18A and 2.5V/16A
10. BASEPLATE GROUNDING: Base-plate should be grounded at one of four screw bolts prior to operation.
11. The converter is provided by basic insulation.
12. “N” for Negative remote ON/OFF.
13. “P” for Positive remote ON/OFF.
www.recom-international.com
April-2005
149