CPCIAC Datasheet, PDF (8/9 Pages) Power System Technology – Standard product AC-DC CompactPCI® 300W

Safety & Installa�on
Cleaning Agents and Process
These converters are components, intended exclusively for integra�on The converters are not herme�cally sealed. In order to avoid possible
into other equipment by an industrial assembly process or by a profes- damage, any penetra�on of liquids shall be avoided.
sionally competent person. Installa�on must strictly follow the safety
regula�ons in respect of the enclosure, moun�ng, creepage and clea-
rance distances, markings of the end-use applica�on.
Connec�on to the system shall be made via the female connector Po-
sitronic.
Pin 45 (Earth) is a leading pin and is connected to the case. For safety
reasons it is essen�al to connect this pin to the protec�ve earth of the
supply system.
The AC/L is internally fused. This fuse is designed to protect the con-
Isola�on
verter against overcurrent caused by a failure, but may not be able to
sa�sfy all requirements. External fuses in the wiring circuit to one or ^{The electric strength test is performed in the factory in accordance with}
both input pins (46 or 47) may be necessary to ensure compliance with ^{IEC/EN 60950.}
local requirements.
Do not open the converters, or the warranty will be invalidated. Make
sure that there is sufficient airflow available for convec�on cooling. This
should be verified by measuring the case of temperature at the speci-
fied measuring point, when the converter is operated in the end-use
Standards and Approvals
The converters are built to meet the safety standards IEC 60950-1, EN
60950-1.
‘Built to meet’ men�onned in the different paragraphs of the datasheet
means that Power System Technology has designed the product to
meet the standard but not cer�fied it in a laboratory.
‘Qualified’ means that the test has been made in a cer�fied laboratory.
Electric Strength
Characteristic
Input to Earth
Electric
Design strength
strength
Factory test for production
units (>10s)
Insulation resistance
1500
2000
Note : If Y op�on is choosen, do not apply dielectric test.
Input to
Output
3000
2000
Temperatures
Output to
Earth
500
500
> 100
Output to
Output
>100
Unit
Vrms
Vdc
Mohms
ഀऀЀԀ଀Ȁ଀ऀЀ฀
ĀȀ̀ЀԀ܀؀
ḀᔀԀ܀ᬀЀ؀ἀ
ᄀ܀ሀጀԀ᐀ᔀ
ĀȀ̀ЀԀ̀؀Ԁ܀
਀ऀ܀ࠀȀ଀ऀЀ
ༀ଀Ѐက ࠀሀ਀က ༀ̀ᄀက ༀ଀Ѐက ࠀሀ਀က ༀ̀ᄀက
ఀЀ଀Ȁ
ࠀऀ਀
ᜀ᠀ᔀጀԀ܀Ѐ؀᐀ᤀᨀᬀᔀᔀᤀᰀᔀጀԀ܀Ѐ؀᐀ᴀ
ࠀऀ਀
଀ఀഀ ࠀ฀਀
଀ഀ਀਀ ࠀ฀਀
଀ఀഀ
଀ഀ਀਀
ༀက
ሀ܀ᤀሀ᠀ᔀጀԀ܀Ѐ؀᐀
ࠀ฀਀
଀ഀऀᘀ ࠀ฀਀
଀ഀऀᘀ
Reliability
MIL-HDBK-217F, notice 2
MTBF ( Hours)
Model
CPCIAC
Heatsink Temp.
40°C
70°C
100°C
GB
285000
139500
86600
GF
165000
82300
51000
CPCI AC Rev. 00
Page 8 of 9
www.powersystemtechnology.com