|
CM500HA-34A Datasheet, PDF (2/4 Pages) Mitsubishi Electric Semiconductor – HIGH POWER SWITCHING USE INSULATED TYPE | |||
|
◁ |
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com
CM500HA-34A
Single IGBTMOD⢠A-Series Module
500 Amperes/1700 Volts
Absolute Maximum Ratings, Tj = 25°C unless otherwise specified
Ratings
Junction Temperature
Storage Temperature
Collector-Emitter Voltage (G-E Short)
Gate-Emitter Voltage (C-E Short)
Collector Current (DC, TC = 110°C)*4
Peak Collector Current (Pulse, Repetitive)*2
Emitter Current (DC, TC = 25°C)*4
Peak Emitter Current (Pulse, Repetitive)*2
Maximum Collector Dissipation (TC = 25°C)*2,*4
Mounting Torque, M6 Main Terminal
Mounting Torque, M6 Mounting
Mounting Torque, M4 G(E) Terminal
Weight
Isolation Voltage (Main Terminal to Baseplate, f = 60Hz, AC 1 min.)
Symbol
Tj
Tstg
VCES
VGES
IC
ICM
IE*1
IEM*1
PC
â
â
â
â
VISO
CM500HA-34A
â40 to 150
â40 to 125
1700
±20
500
1000
500
1000
5000
26
26
13
480
3500
Units
°C
°C
Volts
Volts
Amperes
Amperes
Amperes
Amperes
Watts
in-lb
in-lb
in-lb
Grams
Volts
Static Electrical Characteristics, Tj = 25°C unless otherwise specified
Characteristics
Collector-Cutoff Current
Gate Leakage Current
Gate-Emitter Threshold Voltage
Collector-Emitter Saturation Voltage
Total Gate Charge
Emitter-Collector Voltage*1
Symbol
Test Conditions
Min.
Typ.
Max. Units
ICES
VCE = VCES, VGE = 0V
â
â
1.0
mA
IGES
VGE = VGES, VCE = 0V
â
â
3.0
µA
VGE(th)
VCE(sat)
IC = 50mA, VCE = 10V
IC = 500A, VGE = 15V, Tj = 25°C*3
IC = 500A, VGE = 15V, Tj = 125°C*3
5.5
7.0
8.5
Volts
â
2.3
3.0
Volts
â
2.45
â
Volts
QG
VEC
VCC = 1000V, IC = 500A, VGE = 15V
â
3300
â
nC
IE = 500A, VGE = 0V*3
â
â
3.2
Volts
Dynamic Electrical Characteristics, Tj = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Typ.
Max. Units
Input Capacitance
Cies
â
Output Capacitance
Coes
VCE = 10V, VGE = 0V
â
Reverse Transfer Capacitance
Cres
â
Inductive
Turn-on Delay Time
td(on)
â
Load
Rise Time
tr
VCC = 1000V, IC = 500A,
â
Switch
Turn-off Delay Time
td(off)
VGE1 = VGE2 = 15V, RG = 3.0Ω,
â
Time
Fall Time
tf
Inductive Load
â
Diode Reverse Recovery Time*1
trr
Switching Operation,
â
Diode Reverse Recovery Charge*1
Qrr
IE = 500A
â
*1 Represents characteristics of the anti-parallel, emitter-to-collector free-wheel diode (FWDi).
*2 Pulse width and repetition rate should be such that device junction temperature (Tj) does not exceed Tj(max) rating.
*3 Pulse width and repetition rate should be such as to cause negligible temperature rise.
*4 Case temperature (TC), and heatsink temperature (Tf) measured point is just under the chips.
â
120
nf
â
14
nf
â
2.6 nf
â
900
ns
â
500
ns
â
1200
ns
â
250
ns
â
650
ns
50
â
µC
2
02/10 Rev. 1
|
▷ |