|
ZY1120G Datasheet, PDF (13/17 Pages) Power-One – ZY1120 20A No-Bus POL Data Sheet 3V to 14V Input 0.5V to 5.5V Output | |||
|
◁ |
ZY1120 20A No-Bus POL Data Sheet
3V to 14V Input ï· 0.5V to 5.5V Output
7. Pin Assignments and Description
Pin
Name
Pin Pin Buffer
No. Type Type
Pin Description
Notes
Connect to an external voltage source higher
VLDO
1
P
IM
2
I
PU
Low Voltage Dropout
Interleave Mode
than 4.75V, if VIN<4.75V. Connect to VIN, if
VINâ¥4.75V
Tie to PGND for master or leave open to set
interleave by INTL0â¦INTL4 pins
TEMP
3
A
Temperature Measurement
Analog voltage proportional to junction
temperature of the controller
ENP
4
I
PU
Enable Logic Selection
Tie to PGND for Negative logic or leave open
for Positive logic
Connect a capacitor between the pin and
DELAY
5
A
Power-Up Delay
PGND to program the Power-Up delay. Leave
open for zero delay
CCA2
6
I
PU
Compensation Coefficient Address
Bit 2
Tie to PGND for 0 or leave open for 1
CCA1
7
I
PU
Compensation Coefficient Address
Bit 1
Tie to PGND for 0 or leave open for 1
CCA0
8
I
PU
Compensation Coefficient Address
Bit 0
Tie to PGND for 0 or leave open for 1
VREF
9
A
Voltage Reference
To program the output voltage, connect a
resistor between VREF and TRIM
EN
10
I
PU
Enable
Polarity is determined by ENP pin
OK
11
I/O
PU
Fault Status
Connect to OK pin of other Z-1000 POLs.
Leave open, if not used
SYNC
12
I/O
PU
Frequency Synchronization Line
Connect to SYNC pin of other Z-POLs and/or
to an external clock generator
PGOOD 13
I/O
PU
Power Good
TRIM
14
A
CS
15
I/O
PU
Output Voltage Trim
Current Share/Sense
To program the output voltage, connect a
resistor between VREF and TRIM
Connect to CS pin of other Z-POLs connected
in parallel
INTL4
16
I
PU
Interleave Bit 4
Tie to PGND for 0 or leave open for 1
INTL3
17
I
PU
Interleave Bit 3
Tie to PGND for 0 or leave open for 1
INTL2
18
I
PU
Interleave Bit 2
Tie to PGND for 0 or leave open for 1
INTL1
19
I
PU
Interleave Bit 1
Tie to PGND for 0 or leave open for 1
INTL0
20
I
PU
Interleave Bit 0
Tie to PGND for 0 or leave open for 1
-VS
21
I
PU
Negative Voltage Sense
Connect to the negative point close to the load
+VS
22
I
PU
Positive Voltage Sense
Connect to the positive point close to the load
VOUT
23
P
Output Voltage
PGND
24
P
Power Ground
VIN
25
P
Input Voltage
Legend: I=input, O=output, I/O=input/output, P=power, A=analog, PU=internal pull-up
ZD-00790 Rev. 1.6, 25-Jun-10
www.power-one.com
Page 13 of 17
|
▷ |