 English |
|
|
|
|
|
|
|
| PL2211_07 Datasheet, PDF (4/9 Pages) Power IC Ltd. – Dual Low Noise LDO in 3mm×3mm MLF | |||
| |||
| ◁ |
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter
VIN
DC Supply Voltage at Pin 1
VEN
Enable Input Voltage at Pin 2 and Pin 3
PD
Continuous Power Dissipation
TSTG
Storage Temperature Range
RθJA
TJ,MAX
TL
ESD
Thermal Resistance, Junction-To-Air
Operating Junction Temperature
Lead Temperature (Soldering, 5sec)
ESD Capability, HBM model
RECOMMENDED OPERATING CONDITIONS
Symbol
VIN
VEN
TA
Parameter
DC Supply Voltage at Pin 1
Enable Input Voltage at Pin 2 and Pin 3
Operating Ambient Temperature
Value
-0.3 to +6.0
-0.3 to +6.0
Internally limited
-65 to +150
235
-40 to +125
260
2
Unit
V
V
W
°c
°c/W
°c
°c
kV
Value
Unit
+2.5 to 5.5
V
0 to VIN
V
-40 to +85
°c
ELECTRICAL CHARACTERISTICS
(VIN=VOUT(NOMINAL)+1V or 2.5V (whichever is greater), VEN=VIN, CIN=COUT=1µF, IO=1mA, TA=25°C, unless otherwise noted.)
Symbol
VIN
ÎVOUT
ÎVLOAD
ÎVl LINE
VDP
IO
ILIM
IQ
IG
PSRR
PSRR
VIH
VIL
IEN
Parameter
Supply Voltage
Output Voltage Accuracy
Load Regulation
Line Regulation
dVOUT/( dVIN*VOUT(NOMINAL)
)*100%
Dropout Voltage (Note 1)
Maximum Output Current
Current Limit/Output Current
Standby Current
Ground pin current
Ripple Rejection, IOUT = 10mA,
Test Conditions
IO = 1mA ( both regulator )
IO=1mA to 300mA ( both regulator )
VIN =VOUT(NOMINAL) +0.1V (or 2.5V,
whichever is greater) to 5.5V, IO=1mA
( both regulator )
ILOAD = 300mA ( both regulator )
ILOAD = 100mA ( both regulator )
Continuous
VIN-VOUT =1.3V ( regulator 1 )
VIN-VOUT =1.3V ( regulator 2 )
VEN = 0V
ILOAD1 = ILOAD2 =1mA ( both regulator
active)
f = 100Hz, Cout= 1µF, Cbyp=10nF
f = 10KHz, Cout= 1µF, Cbyp =10nF
Min.
2.5
-1.0
300
350
350
Output voltage noise
COUT = 1µF, CBYP = 10nF,
F = 10Hz to 100K Hz (Vp-p/2/â2)
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Logic Input High Voltage (EN)
( both regulator )
1.2
Logic Input Low Voltage (EN\)
( both regulator )
Logic Input Current (SHDN\)
( both regulator )
-1
Typ.
150
80
600
600
0.02
200
75
70
140
165
20
Max.
5.5
1.0
0.5
0.05
220
100
1
300
0.4
1
Unit
V
%
%
%/V
mV
mV
mARMS
mA
µA
µA
dB
dB
µVRMS
°C
°C
V
V
µA
Note 1: The Dropout Voltage is defined as VIN - VOUT, when VOUT is 2% below the value of VOUT measured for
VIN=VOUT(nominal)+1V.
July 2007
www.picsemi.com
4
© 2007 Power IC. All Rights Reserved.
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese