MB2374 Datasheet, PDF (5/12 Pages) NXP Semiconductors – Dual octal D-type flip-flop; positive-edge trigger (3-State)

Philips Semiconductors
16-bit D-type flip-flop; positive-edge trigger (3-State)
Product specification
MB2374
DC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
T_amb = +25°C
T_amb = –40°C
to +85°C
UNIT
MIN TYP MAX MIN MAX
V_IK
V_OH
V_OL
V_RST
I_I
I_OFF
I_PU/PD
I_OZH
I_OZL
I_CEX
I_O
I_CCH
I_CCL
I_CCZ
∆I_CC
Input clamp voltage
High-level output voltage
Low-level output voltage
Power-up output voltage³
Input leakage current
Power-off leakage current
Power-up/down 3-State
output current⁴
3-State output High current
3-State output Low current
Output High leakage current
Output current¹
Quiescent supply current
Additional supply current per
input pin²
V_CC = 4.5V; I_IK = –18mA
V_CC = 4.5V; I_OH = –3mA; V_I = V_IL or V_IH
V_CC = 5.0V; I_OH = –3mA; V_I = V_IL or V_IH
V_CC = 4.5V; I_OH = –32mA; V_I = V_IL or V_IH
V_CC = 4.5V; I_OL = 64mA; V_I = V_IL or V_IH
V_CC = 5.5V; I_O = 1mA; V_I = GND or V_CC
V_CC = 5.5V; V_I = GND or 5.5V
V_CC = 0.0V; V_O or V_I ≤ 4.5V
V_CC = 2.1V; V_O = 0.5V; V_I = GND or V_CC,
V_OE = GND
V_CC = 5.5V; V_O = 2.7V; V_I = V_IL or V_IH
V_CC = 5.5V; V_O = 0.5V; V_I = V_IL or V_IH
V_CC = 5.5V; V_O = 5.5V; V_I = GND or V_CC
V_CC = 5.5V; V_O = 2.5V
V_CC = 5.5V; Outputs High, V_I = GND or V_CC
V_CC = 5.5V; Outputs Low, V_I = GND or V_CC
V_CC = 5.5V; Outputs 3-State;
V_I = GND or V_CC
V_CC = 5.5V; one input at 3.4V,
other inputs at V_CC or GND
–0.9 –1.2
–1.2 V
2.5 2.9
2.5
V
3.0 3.4
3.0
V
2.0 2.4
2.0
V
0.42 0.55
0.55 V
0.13 0.55
0.55 V
±0.01 ±1.0
±5.0 ±100
±1.0 µA
±100 µA
±5.0 ±50
±50 µA
5.0 50
50
µA
–5.0 –50
–50 µA
5.0 50
50
µA
–50 –70 –180 –50 –180 mA
120 250
250 µA
48
60
60 mA
120 250
250 µA
0.5 1.5
1.5 mA
NOTES:
1. Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
2. This is the increase in supply current for each input at 3.4V.
3. For valid test results, data must not be loaded into the flip-flops (or latches) after applying the power.
4. This parameter is valid for any V_CC between 0V and 2.1V with a transition time of up to 10msec. From V_CC = 2.1V to V_CC = 5V ± 10% a
transition time of up to 100µsec is permitted.
AC CHARACTERISTICS
GND = 0V, t_R = t_F = 2.5ns, C_L = 50pF, R_L = 500Ω
SYMBOL
PARAMETER
WAVEFORM
f_MAX
Maximum clock frequency
1
t_PLH
Propagation delay
t_PHL
nCP to nQx
1
t_PZH
Output enable time
3
t_PZL
to High and Low level
4
t_PHZ
Output disable time
3
t_PLZ
from High and Low level
4
LIMITS
T_amb = +25^oC
V_CC = +5.0V
MIN
TYP
MAX
180
260
1.8
3.4
4.6
1.8
3.6
4.6
1.2
3.0
4.1
2.1
4.0
5.5
1.2
3.4
4.6
1.8
3.6
5.0
T_amb = -40 to
+85^oC
V_CC = +5.0V ±0.5V
MIN
MAX
180
1.8
5.1
1.8
5.1
1.2
4.8
2.1
6.2
1.2
5.1
1.8
5.5
UNIT
MHz
ns
ns
ns
1993 Aug 23
5