MB2823 Datasheet, PDF (4/10 Pages) NXP Semiconductors – Dual 9-bit D-type flip-flop with reset and enable 3-State

Philips Semiconductors Advanced BiCMOS Products
Dual 9-bit D-type flip-flop with
reset and enable (3-State)
Product specification
MB2823
DC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
T_amb = +25°C
T_amb = –40°C
to +85°C
UNIT
MIN TYP MAX MIN MAX
V_IK
Input clamp voltage
V_OH High–level output voltage
V_OL
V_RST
Low–level output voltage
Power-up output low
voltage³
V_CC = 4.5V; I_IK = –18mA
V_CC = 4.5V; I_OH = –3mA; V_I = V_IL or V_IH
V_CC = 5.0V; I_OH = –3mA; V_I = V_IL or V_IH
V_CC = 4.5V; I_OH = –32mA; V_I = V_IL or V_IH
V_CC = 4.5V; I_OL = 64mA; V_I = V_IL or V_IH
V_CC = 5.5V; I_OL = 1mA; V_I = GND or V_CC
–0.9 –1.2
–1.2 V
2.5 2.9
2.5
V
3.0 3.4
3.0
V
2.0 2.4
2.0
V
0.42 0.55
0.55 V
0.13 0.55
0.55 V
I_I
I_OFF
I_PU/PD
I_OZH
I_OZL
I_CEX
I_O
I_CCH
I_CCL
I_CCZ
∆I_CC
Input leakage current
Power-off leakage current
Power-up/down 3-State
output current⁴
3-State output High current
3-State output Low current
Output High leakage current
Output current¹
Quiescent supply current
Additional supply current per
input pin²
V_CC = 5.5V; V_I = GND or 5.5V
V_CC = 0.0V; V_O or V_I ≤ 4.5V
V_CC = 2.1V; V_O = 0.5V; V_I = GND or V_CC,
V_OE = Don’t care
V_CC = 5.5V; V_O = 2.7V; V_I = V_IL or V_IH
V_CC = 5.5V; V_O = 0.5V; V_I = V_IL or V_IH
V_CC = 5.5V; V_O = 5.5V; V_I = GND or V_CC
V_CC = 5.5V; V_O = 2.5V
V_CC = 5.5V; Outputs High, V_I = GND or V_CC
V_CC = 5.5V; Outputs Low, V_I = GND or V_CC
V_CC = 5.5V; Outputs 3–State;
V_I = GND or V_CC
V_CC = 5.5V; one input at 3.4V,
other inputs at V_CC or GND
±0.01 ±1.0
±5.0 ±100
±1.0 µA
±100 µA
±5.0 ±50
±50 µA
5.0 50
50
µA
–5.0 –50
–50 µA
5.0 50
50
µA
–50 –70 –180 –50 –180 mA
120 250
250 µA
45
68
68 mA
120 250
250 µA
0.5 1.5
1.5 mA
NOTES:
1. Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
2. This is the increase in supply current for each input at 3.4V.
3. For valid test results, data must not be loaded into the flip-flops (or latches) after applying the power.
4. This parameter is valid for any V_CC between 0V and 2.1V with a transition time of up to 10msec. From V_CC = 2.1V to V_CC = 5V ± 10% a
transistion time of up to 100µsec is permitted.
AC CHARACTERISTICS
GND = 0V, t_R = t_F = 2.5ns, C_L = 50pF, R_L = 500Ω
SYMBOL
PARAMETER
WAVEFORM
f_MAX
Maximum clock frequency
1
t_PLH
Propagation delay
t_PHL
nCP to nQx
1
t_PHL
Propagation delay
nMR to nQx
2
t_PZH
Output enable time
4
t_PZL
to High and Low level
5
t_PHZ
Output disable time
4
t_PLZ
from High and Low level
5
LIMITS
T_amb = +25^oC
V_CC = +5.0V
MIN
TYP
MAX
140
190
2.0
3.8
5.1
2.5
4.2
5.6
T_amb = -40 to
+85^oC
V_CC = +5.0V ±0.5V
MIN
MAX
140
2.0
5.7
2.5
6.1
3.2
5.3
6.6
3.2
7.5
1.3
3.2
4.4
1.3
5.1
2.2
4.0
5.3
2.2
5.9
1.3
3.3
4.6
1.3
5.1
1.5
3.1
4.4
1.5
5.9
UNIT
MHz
ns
ns
ns
ns
August 24, 1993
5