SA5200 Datasheet, PDF (3/14 Pages) NXP Semiconductors – RF dual gain-stage

Philips Semiconductors
RF dual gain-stage
Product specification
SA5200
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
V_CC
Supply voltage¹
P_D
Power dissipation, T_A = 25°C (still air)²
8-Pin Plastic SO
RATING
-0.5 to +9
780
T_JMAX
P_MAX
T_STG
Maximum operating junction temperature
Maximum power input/output
Storage temperature range
150
+20
–65 to +150
NOTE:
1. Transients exceeding 10.5V on V_CC pin may damage product.
2. Maximum dissipation is determined by the operating ambient temperature and the thermal resistance, θ_JA:
8-Pin SO:
θ_JA = 158°C/W
UNITS
V
mW
°C
dBm
°C
DC ELECTRICAL CHARACTERISTICS
V_CC = +5V, T_A = 25°C; unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS
V_CC Supply voltage
V_CC = 5V, ENABLE = High
I_CC Total supply current
V_CC = 5V, ENABLE = Low
V_CC = 9V, ENABLE = High
V_T
TTL/CMOS logic threshold voltage¹
V_CC = 9V, ENABLE = Low
V_IH Logic 1 level
Power-up mode
V_IL
Logic 0 level
Power-down mode
I_IL
Enable input current
Enable = 0.4V
I_IH
Enable input current
Enable = 2.4V
V_IDC,ODC Input and output DC levels
NOTE:
1. The ENABLE input must be connected to a valid logic level for proper operation of the SA5200.
LIMITS
UNITS
MIN
TYP MAX
4
5.0
9.0
V
6.4
8.4
10.4 mA
95
255
µA
17.8
22.2
mA
320
960
µA
1.25
V
2.0
V_CC
V
-0.3
0.8
V
-1
0
1
µA
-1
0
1
µA
0.6
0.83
1.0
V
AC ELECTRICAL CHARACTERISTICS¹
V_CC = +5V, T_A = 25°C, either amplifier, enable = 5V; unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
MIN
TYP MAX
S21 Insertion gain
f = 100MHz
f = 900MHz
9.2
11
13.2
5.2
7.5
S22 Output return loss
f = 900MHz
–14.3
S12 Reverse isolation
f = 900MHz
–17.9
S11 Input return loss
f = 900MHz
–16.5
P-1 Output 1dB compression point
f = 900MHz
–4.3
NF Noise figure in 50Ω
f = 900MHz
3.6
IP₂
IP₃
ISOL
Input second-order intercept point
Input third-order intercept point
Amplifier-to-amplifier isolation²
f = 900MHz
f = 900MHz
f = 900MHz
+4.3
–1.8
–25
P_OUT
S21
Saturated output power
Insertion gain when disabled
f = 900MHz
f = 100MHz
f = 900MHz
–1.7
–13
–13.5
NOTE:
1. All measurements include the effects of the SA5200 Evaluation Board (see Figure 4). Measurement system impedance is 50Ω.
2. Input applied to one amplifier, output taken at the other output. All ports terminated into 50Ω.
UNITS
dB
dB
dB
dB
dBm
dB
dBm
dBm
dB
dBm
dB
1997 Nov 07
5–3