SSL3401HN Datasheet, PDF (16/29 Pages) NXP Semiconductors – Low voltage dimmable controller for LED lighting

NXP Semiconductors
SSL3401HN
Low voltage dimmable controller for LED lighting
Table 6. Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134).^[1]
Symbol
Parameter
Conditions
V_act(ov)ESD
ESD overvoltage
activation voltage
for LVTSCR-based ESD pin
protection
1 ns to 10 ns rise time
 10 ns rise time
latch-up
Min
[8]
8.2
 8.5
[9] _-
Max
-
-
-
Unit
V
V
-
[1] The following applies to the limiting values:
a) This product includes circuitry designed for the protection of its internal devices from the damaging effects of excessive static
charge. Nonetheless, take conventional precautions to avoid applying static charge > the rated maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to V_SS unless
otherwise noted.
[2] Maximum/minimum voltage above the maximum operating voltage (see Table 7) and below ground that can be applied for a short time
(< 10 ms) to a device without leading to irrecoverable failure. Failure includes the loss of reliability and shorter lifetime of the device.
[3] An ADC input voltage exceeding 3.6 V can be applied for a short time without leading to immediate, unrecoverable failure. Accumulated
exposure to elevated voltages at 4.6 V must be less than 10⁶ s total over the lifetime of the device. Applying an elevated voltage to the
ADC inputs for a long time affects the reliability of the device and reduces its lifetime.
[4] If the comparator is configured with the common-mode input V_IC = V_DD, the other comparator input can be up to 0.2 V above or below
V_DD without affecting the hysteresis range of the comparator function.
[5] Connect an overvoltage protection diode between the analog input pin and the voltage supply pin.
[6] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
[7] Charge device model: Equivalent to charging the IC up to 1 kV and the subsequent discharging of each pin down to 0 V over a 1 
resistor.
[8] Not characterized.
[9] In accordance with NX4-00100.
10. Static characteristics
Table 7. Static characteristics
T_amb = 25 C, unless otherwise specified.
Symbol
Parameter
Conditions
V_DD(3V3)
V_DD(IO)
supply voltage (3.3 V)
input/output supply
voltage
I_DD
Pin RESET
supply current
V_DD(3V3) = V_DD(IO) = 3.3 V
I_IL
LOW-level input current V_I = 0 V;
2.6 V  V_DD(IO)  3.6 V
V_DD(IO) < V_I < 5 V
I_IH
HIGH-level input
V_I = V_DD(IO);
current
V_I
input voltage
pin configured to provide
a digital function;
5 V tolerant pins
V_IH
HIGH-level input
voltage
V_IL
LOW-level input voltage
Min
Typ^[1]
2.6
3.3
2.6
3.3
10
15
50
0
0
-
0.5
[2] ₀
-
0.7V_DD(IO) -
-
-
SSL3401HN
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 28 January 2014
Max
Unit
3.6
V
3.6
V
mA
85
A
0
A
1000
nA
5.0
V
-
V
0.3V_DD(IO) V
© NXP B.V. 2014. All rights reserved.
16 of 29