PI3VDP612-A_11 Datasheet, PDF (5/16 Pages) Pericom Semiconductor Corporation – 4-Lane DisplayPort Rev 1.1a Compliant Switch with Triple Control Logic for Fast Switching

PI3VDP612-A
4-Lane DisplayPort™ Rev 1.1a Compliant Switch
with Triple Control Logic for Fast Switching
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .....................................................–65°C to +150°C
Supply Voltage to Ground Potential ................................–0.5V to +3.6V
Note: Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
DC Input Voltage ............................................................... –0.7V to 3.6V
DC Output Current ....................................................................... 120mA
Power Dissipation ............................................................................ 0.5W
at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Expo-
sure to absolute maximum rating conditions for extended
periods may affect reliability.
DC Electrical Characteristics for Switching over Operating Range (T_A = –40°C to +85°C, V_DD =
3.3V ±10%)
Parameter Description
Test Conditions⁽¹⁾
Min Typ⁽¹⁾ Max Units
VIH
Input HIGH Voltage
Guaranteed HIGH level
VIL
Input LOW Voltage
Guaranteed LOW level
VIK
Clamp Diode Voltage
V_DD = Max., I_IN = –18mA
IIH
Input HIGH Current
V_DD = Max., V_IN = V_DD
1.6
–0.7
0.75 V
–1.2
±5
IIL
Input LOW Current
V_DD = Max., V_IN = GND
±5
µA
I_OFF
I/O leakage when part is off
V_DD = 0V, V_INPUT = 0V to 3.6V
R_ON
On resistance between input to ^VDD ^{= 3.0V, -0.6V<V}INPUT^<0.6V
output
V_DD = 3.0V, 1.0V<V_INPUT<1.5V
50
7
Ohm
10
Ohm
Power Supply Characteristics (T_A = 0°C to +70°C)
Parameter Description
Test Conditions⁽¹⁾
Min
I_CC
Quiescent Power Supply Current
V_DD = Max., V_IN = GND or V_DD
Typ⁽¹⁾ Max
70
Units
µA
Dynamic Electrical Characteristics over Operating Range (T_A = -40º to +85ºC, V_DD = 3.3V ±10%,
GND=0V)
Parameter
Description
Test Conditions
Typ.⁽²⁾ Units
X_TALK
O_IRR
Crosstalk on High Speed Channels
See Fig. 1 for Measurement
Setup
f= 1.35 GHz
f = 100 MHz
-33dB
-48dB
dB
OFF Isolation on High Speed Channels
See Fig. 2 for Measurement
Setup,
f= 1.35 GHz
f = 100 MHz
-33dB
-56dB
I_LOSS
BW_Dx±
BW_AUX/HPD
Differential Insertion Loss on High
Speed Channels
Bandwidth -3dB for Main high speed
path (Dx±)
-3dB BW for AUX and HPD signals
@2.7Gbps (see figure 3)
See figure 3
See figure 3
-1.5
dB
3.25
GHz
1.5
GHz
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_DD = 3.3V, T_a = 25°C ambient and maximum loading.
11-0103
5
PS9056A
07/12/11