 English |
|
|
|
|
|
|
|
| PI3USB102E Datasheet, PDF (4/7 Pages) Pericom Semiconductor Corporation – USB 2.0 High-Speed (480 Mbps) Switch with 5V Protection | |||
| |||
| ◁ |
PI3USB102E
USB 2.0 High-Speed (480 Mbps) Switch with 5V Protection
Power Supply Characteristics
Parameters
Description
Test Conditions(1)
Min. Typ. Max. Units
IDD
Power Supply Current VDD = 3.3V, OE = GND, VSEL = GND or VDD
1
2
uA
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. VDD = 3.0 - 5.5V, TA = 25°C ambient.
3. Measured by the voltage drop between Y+/Y- and the lower of M+/M- and D+/D- at indicated current through the Switch.
4. When the voltage at Y+/Y- is greater than VDD + 0.2V, over-voltage protection limits the output voltage at M+/- and D+/- to protect connected devices from
damage.
Capacitance (Ta = 25°C, VDD = 3.3V, f = 1MHz)
Parameters(3)
Description
Test Conditions(1) Typ.(2)
Max.
Units
CIN
Input Capacitance
COFF (M/D)
Switch Off Capacitance for M and D ports OE = High
COFF (Y)
Switch Off Capacitance for Y port
OE = High
CON
Switch Capacitance, Switch ON
VSEL = 0V or VDD
Dynamic Electrical Characteristics Over the Operating Range
Parameters(3)
Description
Test Conditions
2.2
3.2
3.0
4.0
pF
5.0
6.0
6.0
7.0
Min. Typ.(2) Max. Units
XTALK
OIRR
Crosstalk
OFF Isolation
RL = 50â¦, f = 240 MHz
-29
dB
-28
-3dB BW
â3dB Bandwidth
RL = 50â¦
1,000
MHz
-0.5dB BW
â0.5dB Bandwidth
RL = 50â¦
275
MHz
TOVP
Over-Voltage Response Time(4)
CL = 10 pF, VY+/Y- = 5V,
VDD = 3.0 to 3.6V (6)
40 100 ns
VDSW
Dynamic Signal Output Swing(5)
CL = 10 pF, VY+/Y- = 5V,
VDD = 3.0 to 3.6V (6)
2.7 3.0 3.6 V
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VDD = 3.3V, TA = 25°C ambient.
3. This parameter is determined by device characterization but is not production tested.
4. Time duration for output voltage higher than VOVP when input is connected to 5V.
5. Output voltage observed at M+/M- and D+/D- during over-voltage condition.
6. Tested using a 750 kHz square wave with tr = 75 ns and tf = 75 ns.
Switching Characteristics
Parameters Description
Test Conditions (1) Min. Typ. Max. Units
tPD
Propagation Delay(2,3)
0.25
tPZH, tPZL Line Enable Time - SEL, OE to D(+/-), M(+/-)
0.5
50
ns
tPHZ, tPLZ Line Disable Time - SEL, OE to D(+/-), M(+/-)
See Test Circuit
0.5
11.0
tBBM
tSKb-b
Break Before Make Delay
Output skew, bit-to-bit (opposite transition of the same
output (tPHL-tPLH)(2)
for Electrical
Characteristics
9.0
ns
8
20
ps
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Guaranteed by design.
3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the
switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little
propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and
its interactions with the load on the driven side.
14-0135
4
08/05/14
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese