PI3L100 Datasheet, PDF (2/6 Pages) Pericom Semiconductor Corporation – 3.3V, Wide Bandwidth Quad 2:1 Mux/Demux LanSwitch

PI3L100
112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122³3344^.35566^V7788^,99^W001122ⁱ33^d4455^e6677^B8899^a00ⁿ1122^d3344^w5566ⁱ77^d8899^t00^h1122^Q1122^u3344^a55^d6677²8899^:00¹1122^, 33^M445566^u77^x8899^/00^D1122^e33^m445566^u7788^x9900^L1122^a11ⁿ2233^S4455^w6677ⁱ88^t99^c00^h1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ............................................................. –65°C to +150°C
Ambient Temperature with Power Applied ................................. 0°C to +70°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ...... –0.5V to +4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only) ... –0.5V to +4.6V
DC Input Voltage ..................................................................... –0.5V to +4.6V
DC Output Current ............................................................................... 120 mA
Power Dissipation ......................................................................................0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure
to absolute maximum rating conditions for ex-
tended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, T_A = 0°C to +70°C, V_CC = 3.3V ±5%)
Parameters
Description
Test Conditions(1)
Min. Typ⁽²⁾ Max. Units
V_IH
Input HIGH Voltage
V_IL
Input LOW Voltage
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
2.0 —
–0.5 —
—
V
0.8
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
— — ±1
I_IL
Input LOW Current
V_CC = Max., V_IN = GND
— — ±1 µA
I_OZH High Impedance Output Current 0 ≤ A, B ≤ V_CC
— — ±1
V_IK Clamp Diode Voltage
I_OS
Short Circuit Current⁽³⁾
V_CC = Min., I_IN = –18mA
A (B) = 0V, B (A) = V_CC
— –1.2 V
100 — — mA
V_H
Input Hysteresis at Control Pins
— 150 — mV
R_ON(6) Switch On Resistance
V_CC = Min., V_IN = 0V, I_ON = 48mA
—
5
7
V_CC = Min., V_IN = 2.4V, I_ON = 15mA —
10
15 Ω
∆R_ON On Resistance Match
V_IN = 3.0V, E = LOW
— ——
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient temperature.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. VON (min) value is at V_CC = 3.3V, T_A = 70°C.
Capacitance (TA = 25°C, f = 1 MHz)
Parameters⁽¹⁾ Description
C_IN
C_OFF
C_ON
C_OFF
Input Capacitance
Capacitance, Switch Off (Y)
Capacitance, Switch On
Capacitance, Switch Off (A/B)
Test Conditions
VIN = 0V
VIN = 0V
VIN = 0V
VIN = 0V
Note:
1. This parameter is determined by device characterization but is not production tested.
Typ Max. Units
3
pF
17
pF
25
pF
8
pF
2
PS8504 11/13/00