PI3A3160C Datasheet, PDF (2/7 Pages) Pericom Semiconductor Corporation – 3.0V, SOTiny™ 0.8Ω Dual SPDT Analog Switch with -1.0V to 4.2V Operating Range

PI3A3160C
3.0V, SOTiny^™ 0.8Ω Dual SPDT Analog Switch
with -1.0V to 4.2V Operating Range
Absolute Maximum Ratings
Voltages Referenced to GND
V_CC ...................................................................... –0.5V to 4.6V
V_IN, V_COM, V_NC, V_NO ⁽¹⁾ ......................... –1.5V to V_CC +0.3V
or 30mA, whichever occurs first
Current (any terminal)................................................... ±200mA
Peak Current, COM, NO, NC
(Pulsed at 1ms, 10% duty cycle)................................... ±400mA
Temp Range ...................................................... -40°C to + 85°C
Thermal Information
Continuous Power Dissipation
TDFN-12 (derate 7.1mW/ºC above +70ºC)........................ 0.5W
Storage Temperature ........................................ –65ºC to +150ºC
Lead Temperature (soldering, 10s) ................................. +300ºC
Notes:
1. Signals on NC, NO, COM, or IN exceeding V_CC or GND are clamped by internal diodes. Limit forward diode current to 30mA.
Caution: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a
stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of
this specification is not implied.
Electrical Specifications - Single +3.3V Supply
(V_CC = +3.3V ± 10%, GND = 0V, V_IH = 1.4V, V_IL = 0.5V)
Parameter
Symbol
Conditions
Min.⁽¹⁾ Typ. ⁽²⁾ Max. ⁽¹⁾ Units
Analog Switch
Analog Signal Range ⁽³⁾
V_ANALOG
–1.0
On-Resistance
On-Resistance Match Be-
tween Channels⁽⁴⁾
R_ON
∆R_ON
V_CC= 2.7V,
I_COM = 100mA,
V_NO or V_NC = +1.5V
On-Resistance Flatness⁽⁵⁾
R_FLAT(ON)
V_CC= 2.7V, I_COM = 100mA,
V_NO or V_NC = 0.8V, 2.0V
NO or NC Off Leakage Cur- I_NO(OFF) or V_CC = 3.3V, V_COM = 0V,
rent⁽⁶⁾
I_NC(OFF) V_NO or V_NC = +2.0V
–2
COM
On Leakage Current⁽⁶⁾
I_COM(ON)
V_CC = 3.3V, V_COM = +2.0V,
V_NO or V_NC = +2.0V
–2
V_CC
V
1.3
0.15
Ω
0.1
2
µA
2
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
T_A = 40°C to +85°C.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
Typical values are tested w T_A = 25°C
3. Guaranteed by design.
4. ∆R_ON = R_ON max. - R_ON min.
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25°C.
PS8795B
02/24/06
2