PI2DBS6212 Datasheet, PDF (2/7 Pages) Pericom Semiconductor Corporation – 6.5 Gbps SAS2, SATA3, XAUI 2 Differential Channel, 2:1 Mux/DeMux Switch

PI2DBS6212
6.0 Gbps SAS2, SATA3, XAUI
2 Differential Channel, 2:1 Mux/DeMux Switch
Maximum Ratings
(Above which useful life may be impaired.For user guidelines, not tested.)
Storage Temperature.......................................... –65°C to +150°C
Supply Voltage to Ground Potential .................... –0.5V to +2.5V
DC Input Voltage.................................................. –0.5V to +V_DD
DC Output Current ........................................................... 120mA
Power Dissipation................................................................. 0.5W
Note: Stresses greater than those listed under MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
Power Supply Characteristics
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾
I_DD
Quiescent PowerSupply Current
V_DD = Max., V_IN = GND or V_DD
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_DD = 1.8V, T_a = 25°C ambient and maximum loading.
Max.
400
Units
µA
DC Electrical Characteristics for Switching over Operating Range
(T_A = –40°Cto +85°C, V_DD = 1.5V to 1.8V ±10%)
Parameter
Description
Test Conditions
Min.
V_IH
Input HIGH Voltage, SEL input Guaranteed HIGH level
0.65 x V_DD
V_IL
Input LOW Voltage, SEL input Guaranteed LOW level
-0.5
V_IK
Clamp Diode Voltage, SEL input V_DD = Max., I_IN = –18mA
-
I_IH
Input HIGH Current for SEL
V_DD = Max., V_IN = V_DD
-10
I_OZ
Channel Leakage Current
V_DD = Max., V_IN = 1.8V
-10
I_IL
Input LOW Current
V_DD = Max., V_IN = GND
-20
V_IDC DC Signal Voltage Range
V_O/V_I > 95%, R_L = 10K
-0.5
V_O/V_I > 80%, R_L = 50-Ohms
-0.4
Typ.
Max. Units
-
-
- 0.35 x V_DD V
-0.7
-1.2
-
+10
-
+10
μA
-
+10
2.5
V
1.2
Switching Characteristics
(T_A= -40º to +85ºC, VDD = 1.5V to 1.8V ±10%)
Parameter
Description
Min. Typ.
tPZH, tPZL
tPHZ, tPLZ
tb-b
tch-ch
tdiff
Line Enable Time - SEL to AN, BN, CN
Line Disable Time - SEL to AN, BN, CN
Bit-to-bit skew within the same differential pair
Channel-to-channel skew
Differential delay - ^AN ^{to BN or CN}
0.5
-
0.5
-
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Max.
9.0
9.0
10
15
20
Units
ns
ps
14-0031
2
www.pericom.com
03/26/2014