AMG8831 Datasheet, PDF (6/6 Pages) Panasonic Semiconductor – Infrared Array Sensor Grid-EYE

Infrared Array Sensor Grid-EYE (AMG88)
6) To prevent the insulation of the PC
board after soldering, please be careful
not to place the chemicals on the sensor
when coating.
7. Connections
1) Please perform connections correctly
in accordance with the terminal
connection diagram. In particular, be
careful not to reverse wire the power
supply as this will cause damage or
degrade to the sensor.
2) Please do not connect wires in an
empty terminal. It causes the sensor
breakdown.
3) When using the sensors with cables, it
is recommended that cables which are
shielded and as short as possible be
used in order to safeguard against the
effects of noise.
8. Cleaning
Avoid ultrasonic cleaning since this may
cause breaks or disconnections in the
wiring.
9. Transportation and storage
1) Extreme vibration and shock during
transport will damage the sensor. Handle
the outer box and reel with care.
2) Storage under extreme conditions will
cause soldering degradation, external
appearance defects, and deterioration of
the characteristics. The following storage
conditions are recommended.
• Temperature: 0 to 45°C 32 to 113°F
• Humidity: less than 70% R.H.
• Atomosphere: No harmful gasses such
as sulfurous acid gas, minimal dust.
3) The sensors are sensitive to moisture
and come in moisture-proof packages.
Observe the following cautions when
storing.
• After the moisture-proof package is
unsealed, take the sensors out of storage
as soon as possible (within 1 week
30°C 86°F/60% R.H.).
• If the sensors are to be left in storage for
a considerable period after the moisture-
proof package has been unsealed, it is
recommended to keep them in another
moisture-proof bag containing silica gel
(within 3 months at the most).
*When mounting with solder, if thermal
stress is applied to sensors that have
absorbed moisture, the moisture will
vaporize, swelling will occur, and the
inside of the package will become
stressed. This may cause the package
surface to blister or crack. Therefore,
please take caution and observe the
soldering conditions.
10. Special remarks
Although the best attention will be paid
for the quality controls of the products,
please consider the followings:
1) To prevent unexpected failures as
much as possible under the conditions
not shown in this specifications, please
let us know the detailed information on
the application, such as the
environmental, operational and mounting
condition.
2) By any chance, if the failure of the
product is considered to cause a
personal injury or death or property
damage, the safety rate should be added
to the specified values shown in this
specifications and the dual safety
structure or circuit is recommended to be
taken from the stand point of the product
liability indemnity.
3) We will either repair or replace any
products or parts there of which prove to
be defective against only the items
written in this specifications within 1 year
from the date of products acceptance at
the site of delivery. Following cases are
not covered by this guarantee.
• The case of other damage caused by
the failure or defect of the product.
• The case that the product condition
changed by handling, storage and/or
transportation after delivery.
• The case caused by the phenomenon
which has never been discovered and is
impossible to be foreknown with the
existing technologies.
• The case of force majeure, such as acts
of God, public enemy or war, fires, floods
and any other causes beyond the control
of the people concerned.
11. Export control
[To customers in Japan]
This product is restricted under Japan’s
“Foreign Exchange and Foreign Trade
Law.” An export permit from the
Japanese government is required when
you export or take this product outside
Japan. (As of Apr.2011)
This product may not be used for any
purpose other than those specified.
Reselling the product to third parties is
prohibited. When disposing of the
product, it must first be converted into
non-reusable and non-controlled form.
[To customers outside Japan]
This product is restricted under Japan’s
laws and regulations relating to security
export control (Foreign Exchange and
Foreign Trade Law). We have obtained an
export permit from the Japanese
government to sell or provide this product
to your company, subject to the following:
This product may not be used for any
purpose other than those specified. This
product may be subject to further export
restrictions under the laws and
regulations of other countries (including
your own). Reselling the product to third
parties is prohibited. When disposing of
the product, it must first be converted into
non-reusable and non-controlled form.
Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e
ASCTB22E 201201-T