English
Language : 

ARE10A12 Datasheet, PDF (5/5 Pages) Panasonic Semiconductor – 2.6 GHz SMALL MICROWAVE RELAYS
RE (ARE)
• 75Ω type
CAD Data
(0.7)
20.2
(.028)
.795
13.2 ±0.5 11.2
.520 ±.020 .441
(1.3)
(.511)
8.6
.339
0.3
.012
0.3
.012
9.6
.378
0.3
.012
2.54
0.5
(1.49) 7.62 (2.09)
.100
.020
(.059) .300 (.082)
General tolerance: ±0.3 ±.012
Note: Please consult us regarding recommended PC board patterns.
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different.
2. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
It is recommended that alcoholic solvents
be used.
3. Soldering
(Standard PC board terminal)
1) The manual soldering shall be
performed under following condition.
Max. 260°C 500°F 10s
Max. 350°C 662°F 3s
The affect of the PCB on the relay will
differ depending on the type of PCB
used. Please verify the type of PCB to be
used.
Preheat according to the following
conditions.
Temperature
120°C 248°F or less
Time
Within 2 minute
Soldering should be done at 260±5°C
500±9°F within 6 s.
2) In case of automatic soldering, the
following conditions should be observed
(Surface-mount terminal)
(1) Position of measuring temperature
A
A: Surface of PC board where relay is mounted.
(2) IR (infrared reflow) soldering method
T3
T2
T1
T1=155 to 165°C
311 to 329°F
T2=180 to 200°C
356 to 392°F
T3=245°C max.
473°F max.
t1
t2
t1= within 120s
t2=within 30s
Temperature rise of relay itself may vary
according to the mounting level or the
heating method of reflow equipment.
Therefore, please set the temperature of
soldering portion of relay terminal and
the top surface of the relay case not to
exceed the above mentioned soldering
condition.
It is recommended to check the
temperature rise of each portion under
actual mounting condition before use.
4. Packing style
1) Tape dimensions
1.5+−00.1 .059+−.0004 dia.
4
Relay polarity bar
.157
2.0±0.15
.079±.006
1.75
.069
0.4
.016
1.7
.067
R0.75
.030
1.5 .059
RE Relay 20.0
.787
Tape coming out direction
20.2 44±0.3
20.75.795 1.732±.012
.817 40.4
1.591
13.85
.545
10.6+−00..23
.417+.008
−.012
2) Dimensions of plastic reel
21±0.8 dia.
.827±.031 dia.
2.0±0.5
.079±.020
Max. 95
3.740
13±0.2 dia.
.512±.008 dia.
45.5+−00.2
1.791+−.0008
Max. 51.7
2.035
380±0.2
14.961±.008
5. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
Schematic (Top view)
NC COM NO
14 13 12 11 10 9 8
Direction indication
1
7
(Deenergized condition)
(1) Temperature:
–40 to +70°C –40 to +158°F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
Humidity, %R.H.
85
Tolerance range
(Avoid freezing
when used at
temperatures
lower than
0°C 32°F)
5
(Avoid
condensation
when used at
temperatures
higher than
0°C 32°F)
–40
0
–40
+32
Temperature, °C °F
70
+158
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C 32°F. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
For general cautions for use, please
refer to the “General Application
Guidelines”.
Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e/
ASCTB104E 201202-T