HP2-AC24V Datasheet, PDF (4/7 Pages) Panasonic Semiconductor – Relay for control panel of 10A (2c/3c/4c) Food processing packing machines

HP
2. Specifications
Characteristics
Contact
Rating
Electrical
characteristics
Item
Arrangement
Contact resistance (Initial)
Contact material
2 Form C, 3 Form C
4 Form C
Nominal switching capacity
Min. switching capacity (Reference value)*¹
Insulation resistance (Initial)
Between open contacts
Breakdown voltage
(Initial)
Between contact sets
Between contact and coil
Temperature rise (coil)
Operate time*²
Mechanical
characteristics
Expected life
Conditions
Unit weight
Release time*²
Shock resistance
Vibration resistance
Mechanical
Functional
Destructive
Functional
Destructive
Conditions for operation, transport and storage*³
Max. Operating speed
Specifications
2 Form C, 3 Form C, 4 Form C
Max. 15 mΩ (By voltage drop 6 V DC 1A)
Ag
Ag alloy (cd free)
10A 250V AC (resistive load)
100mA 5V DC
Min. 100MΩ (at 500V DC) Measurement at same location as “Breakdown voltage” section.
1,000 Vrms for 1min (2 Form C, 4 Form C).
2,000 Vrms for 1min (3 Form C) (Detection current: 10mA.)
1,500 Vrms for 1min (2 Form C, 4 Form C).
2,000 Vrms for 1min (3 Form C) (Detection current: 10mA.)
1,500 Vrms for 1min (2 Form C, 4 Form C).
2,000 Vrms for 1min (3 Form C) (Detection current: 10mA.)
Max. 65°C 149°F (By temperature method, at 40°C, nominal current)
Max. 25ms (2 Form C), Max.30ms (3 Form C, 4 Form C)
(Nominal coil voltage applied to the coil, excluding contact bounce time.)
Max. 25ms (2 Form C), Max.30ms (3 Form C, 4 Form C)
(Nominal coil voltage applied to the coil, excluding contact bounce time.) (without diode)
Min. 98 m/s² (Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
Min. 980 m/s² (Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 1 mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 2 mm
Min. 10⁷
Ambient temperature: –50°C to +40°C –58°F to +104°F
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 times/min. (at max. rating)
2 Form C: approx. 60g 2.12oz, 3 Form C: approx. 100g 3.53oz, 4 Form C: approx. 125g 4.41oz
Notes: *1. This value can change due to the switching frequency, environmental conditions and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. For the AC coil types, the operate/release time will differ depending on the phase.
*3. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
conditions in NOTES.
3. Electrical life
1) AC load
Voltage
Load
125V AC
250V AC
Resistive load (A) (cosϕ=1) Inductive load (A) (cosϕ=0.4) Resistive load (A) (cosϕ=1) Inductive load (A) (cosϕ=0.4)
—
—
10
7.5
10
7.5
7.5
5
Current
5
3
3
2
1
0.7
0.6
0.4
Note: When the electromagnet or exciting coil (Solenoid, etc.) is the load, the value of motor or lamp load is applicable.
Expected life
Min. 2×10⁵
Min. 5×10⁵
Min. 10⁶
Min. 2×10⁶
2) DC load
Voltage
Load
Current
Resistive load (A)
—
7.5
5
1
24V DC
Inductive load (A)
7
5
3
0.6
Resistive load (A)
—
0.5
0.3
0.1
125V DC
Inductive load (A)
—
0.4
0.2
0.06
Expected life
Min. 2×10⁵
Min. 5×10⁵
Min. 10⁶
Min. 2×10⁶
Notes: 1. For DC inductive loads, use an arc suppressing circuit.
2. Cautions at DC load use
When used under a DC load operating at high repetition rate with considerable arcing, corrosion of the contacts and/or the contact blades is likely to occur.
ASCTB81E 201201-T
Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e