HAE100-12S3P3 Datasheet, PDF (1/5 Pages) Power Mate Technology Co., LTD – OUTPUT CURRENT UP TO 25A

Standard
Terminal Block
FEATURES
z OUTPUT CURRENT UP TO 25A
z 2:1 WIDE INPUT VOLTAGE RANGE
z HIGH EFFICIENCY UP TO 93%
z NO MINIMUM LOAD
z SOFT-START
z ADJUSTABLE OUTPUT VOLTAGE
z UNDER-VOLTAGE LOCKOUT
• INPUT REVERSE PROTECTION
• INDUSTRY STANDARD HALF-BRICK FOOTPRINT
• SIX-SIDED CONTINUOUS SHIELD
• INPUT TO OUTPUT BASIC INSULATION
• BUS TERMINAL BLOCK OPTION
APPLICATIONS
Wireless Network
Telecom/ Datacom
Industry Control System
Distributed Power Architectures
Semiconductor Equipment
OPTIONS
z Positive logic remote ON/OFF
z Pin length
z Terminal block z Terminal block with EMC filter
z Heat-sink
DESCRIPTION
HAE100-SERIES DC/DC converters provide up to 100 watts of output power in an
industry standard half-brick package and footprint. All models feature a wide input
range and adjustable output voltage.
T E C H N I C A L S P E C I F I C A T I O N All specifications are typical at nominal input, full load and 25℃ otherwise noted
OUTPUT SPECIFICATIONS
GENERAL SPECIFICATIONS
Output power
100Watts, max. Efficiency
See table
Voltage accuracy
Voltage adjustability (Note 7)
Minimum load
Line regulation
Load regulation
Remote sense (Note 8)
Ripple and noise
Temperature coefficient
Transient response recovery time
Over voltage protection threshold
Over current protection threshold
Full load and Vin, nom
±1% _{Isolation voltage}
+10%, -20%
Input to Output (Basic insulation) 2250VDC, min.
Input (Output) to Case
1600VDC, min.
0% ^{Isolation resistance}
109ohms, min.
LL to HL at FL
See table ^{Isolation capacitance}
2500pF, max.
No Load to Full Load
See table ^{Switching frequency}
300KHz, typ.
10% of Vout, nom ^{Design meet safety standard}
IEC60950-1, UL60950-1, EN60950-1
20MHz bandwidth
See table ^{Case material}
Metal
±0.02%/ ℃, max. ^{Base material}
FR4 PCB
25% load step change
200μS ^{Potting material}
(Hiccup) 115% ~ 130% of Vout, nom ^Dimensions
Silicon (UL94-V0)
2.40 X 2.28 X 0.50 Inches
(61.0×57.9×12.7 mm)
110% ~ 140% of Iout Rated _Weight
97g (3.42oz)
Short circuit protection
INPUT SPECIFICATIONS
Input voltage range
Hiccup, automatics recovery
MTBF (Note 1)
BELLCORE TR-NWT-000332
MIL-HDBK-217F
1.010 x 106 hrs
7.416 x 104 hrs
12V nominal input
24V nominal input
48V nominal input
9 – 18VDC ^{ENVIRONMENTAL SPECIFICATIONS}
18 – 36VDC Operating ambient Without Heat-sink -40℃ ~ +35℃ (without derating)
36 – 75VDC temperature (Note10)
+35℃ ~ +77℃ (with derating)
Start-up voltage
12V nominal input
24V nominal input
8.5VDC (For 3.3,5,12,15Vout) With Heat-sink
17.5VDC
(0.24” Height)
-40℃ ~ +50℃ (without derating)
+50℃ ~ +82℃ (with derating)
Shutdown voltage
48V nominal input
12V nominal input
24V nominal input
48V nominal input
35.5VDC Operating ambient Without Heat-sink
7.5VDC temperature (Note10)
16VDC (For 24,28,48Vout) With Heat-sink
34VDC
(0.24” Height)
-40℃ ~ +30℃ (without derating)
+30℃ ~ +81℃ (with derating)
-40℃ ~ +44℃ (without derating)
+44℃ ~ +85℃ (with derating)
Input filter
Pi type Maximum case temperature
105℃
Input surge voltage 100mS max
12V nominal input
36VDC _{Over temperature protection}
24V nominal input
48V nominal input
50VDC
100VDC
Storage temperature range
Input reverse protection (Note 9)
Parallel diode
Thermal impedance
(Note 11)
without Heat-sink
with 0.24" Height Heat-sink
Start up time
Vin, nom and
constant resistive load
Power up
Remote ON/OFF
Remote ON/OFF (Note 6)
25mS, typ.
25mS, typ. _{Thermal shock}
with 0.45" Height Heat-sink
(Negative logic) (Standard)
DC-DC ON Short or 0V < Vr < 1.2V ^Vibration
115℃
-55℃ to +125℃
6.7℃/watt
5.4℃/watt
4.7℃/watt
MIL-STD-810F
MIL-STD-810F
(Positive logic) (Option)
Input current of Remote control pin
DC-DC OFF
DC-DC ON
DC-DC OFF
Vin(nom)
Open or 3V < Vr < 12V Relative humidity
Open or 3V < Vr < 12V
Short or 0V < Vr < 1.2V
EMC CHARACTERISTICS (Note 12)
-0.5mA ~ 1mA ^EMI
EN55022
5% to 95% RH
Class A
Remote off input current
Vin(nom)
3mA _ESD
EN61000-4-2
Air
Contact
±
±
8KV
6KV
Perf.
Criteria
A
Radiated immunity
EN61000-4-3
10 V/m Perf. Criteria A
Fast transien
EN61000-4-4
± 2KV Perf. Criteria A
Surge
EN61000-4-5
± 1KV Perf. Criteria A
Conducted immunity EN61000-4-6
10 Vr.m.s Perf. Criteria A
Page 1 of 5 Issued Date：2009/01/13