MC74VHC595_15 Datasheet, PDF (4/11 Pages) ON Semiconductor – 8-Bit Shift Register with Output Storage Register

MC74VHC595
FUNCTION TABLE
Inputs
Resulting Function
Operation
Clear shift register
Shift data into shift
register
Registers remains
unchanged
Reset
(SCLR)
L
H
Serial
Input
(SI)
X
D
H
X
Shift
Clock
(SCK)
X
↑
L, H, ↓
Reg
Clock
(RCK)
L, H, ↓
L, H, ↓
X
Output
Enable
(OE)
L
L
L
Shift
Register
Contents
L
D→SR_A;
SR_N→SR_N+1
U
Storage
Register
Contents
U
U
**
Serial
Output
(SQH)
Parallel
Outputs
(QA − QH)
L
U
SR_G→SR_H
U
U
**
Transfer shift register
H
contents to storage
register
Storage register remains
X
unchanged
X
L, H, ↓
↑
L
X
X
L, H, ↓
L
U
SR_N³STR_N
*
*
U
*
SR_N
U
Enable parallel outputs
X
X
X
X
L
*
**
*
Enabled
Force outputs into high
X
X
X
X
H
*
impedance state
**
*
Z
SR = shift register contents
D = data (L, H) logic level
STR = storage register contents U = remains unchanged
↓ = High−to−Low
↑ = Low−to−High
* = depends on Reset and Shift Clock inputs
** = depends on Register Clock input
MAXIMUM RATINGS*
Symbol
Parameter
Value
Unit
V_CC DC Supply Voltage
– 0.5 to + 7.0
V
V_in DC Input Voltage
– 0.5 to + 7.0
V
V_out DC Output Voltage
– 0.5 to V_CC + 0.5 V
I_IK Input Diode Current
− 20
mA
I_OK Output Diode Current
± 20
mA
I_out DC Output Current, per Pin
± 25
mA
I_CC DC Supply Current, V_CC and GND Pins
± 50
mA
P_D Power Dissipation in Still Air,
SOIC Packages†
500
mW
TSSOP Package†
450
T_stg Storage Temperature
– 65 to + 150
_C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating — SOIC Packages: – 7 mW/_C from 65_ to 125_C
TSSOP Package: − 6.1 mW/_C from 65_ to 125_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min Max Unit
V_CC DC Supply Voltage
2.0 5.5 V
V_in
DC Input Voltage
0
5.5
V
V_out DC Output Voltage
0
V_CC
V
T_A
Operating Temperature, All Package Types
− 55 + 125 _C
t_r, t_f
Input Rise and Fall Time
V_CC = 3.3V ±0.3V 0
V_CC =5.0V ±0.5V 0
100 ns/V
20
Functional operation above the stresses listed in the Recommended Operating Ranges is not
implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may
affect device reliability.
www.onsemi.com
4