|
MC74LVX50 Datasheet, PDF (4/10 Pages) ON Semiconductor – HEX BUFFER | |||
|
◁ |
MC74LVX50
DC ELECTRICAL CHARACTERISTICS
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
Parameter
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIH HighâLevel Input Voltage
Test Conditions
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIL LowâLevelInputVoltage
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VOH HighâLevelOutputVoltage
(VIN= VIH or VIL)
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VOL LowâLevelOutputVoltage
(VIN= VIH or VIL)
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ IIN InputLeakageCurrent
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ ICC QuiescentSupplyCurrent
IOH = â50 mA
IOH = â50 mA
IOH = â4 mA
IOL = 50 mA
IOL = 50 mA
IOL = 4 mA
VIN = 5.5 V or GND
VIN = VCC or GND
VCC
TA = 25°C
TA ⤠85°C
(V) Min Typ Max Min Max Unit
2.0 1.5
3.0 2.0
3.6 2.4
1.5
V
2.0
2.4
2.0
0.5
0.5
V
3.0
0.8
0.8
3.6
0.8
0.8
2.0 1.9 2.0
1.9
V
3.0 2.9 3.0
2.9
3.0 2.58
2.48
2.0
0.0 0.1
0.1
V
3.0
0.0 0.1
0.1
3.0
0.36
0.44
0 to
±0.1
±1.0 mA
3.6
3.6
2.0
20.0 mA
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ AC ELECTRICAL CHARACTERISTICS Input tr = tf = 3.0 ns
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ tPLH,
tPHL
Parameter
Propagation Delay,
Input A to Y
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ tOSHL
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ tOSLH
OutputâtoâOutput Skew
(Note 7)
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ CIN InputCapacitance
Test Conditions
VCC = 2.7 V
CL = 15 pF
CL = 50 pF
VCC = 3.3 V ± 0.3 V CL = 15 pF
CL = 50 pF
VCC = 2.7 V
CL = 50 pF
VCC = 3.3 V ±0.3V CL = 50 pF
TA = 25°C
TA ⤠85°C
Min Typ Max Min Max Unit
5.4 10.1 1.0 12.5
ns
7.9 13.6 1.0 16.0
4.1 6.2 1.0 7.5
6.6 9.7 1.0 11.5
1.5
1.5
ns
1.5
1.5
4
10
10
pF
Typical @ 25°C, VCC = 3.3 V
CPD
Power Dissipation Capacitance (Note 8)
15
pF
7. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGHâtoâLOW (tOSHL) or LOWâtoâHIGH (tOSLH); parameter
guaranteed by design.
8. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the noâload dynamic
power consumption; PD = CPD VCC2 fin + ICC VCC.
NOISE CHARACTERISTICS Input tr = tf = 3.0ns, CL = 50pF, VCC = 3.3 V
TA = 25°C
Symbol
Characteristic
Typ
Max
Unit
VOLP Quiet Output Maximum Dynamic VOL
0.3
0.5
V
VOLV Quiet Output Minimum Dynamic VOL
â0.3
â0.5
V
VIHD Minimum High Level Dynamic Input Voltage
2.0
V
VILD Maximum Low Level Dynamic Input Voltage
0.8
V
http://onsemi.com
4
|
▷ |