LC78616PE Datasheet, PDF (4/26 Pages) ON Semiconductor – Compact Disc Player IC

LC78616PE
Electrical Characteristics at Ta=40 to 85°C, VDD=3.0 to 3.6V, DVSS=AVSS=XVSS=VVSS1=0V
Parameter
Symbol
Pin Names
Type Conditions MIN
TYP MAX Unit
Current drain
IDD1
DVDD, AVDD,
XVDD, VVDD1
40
(T.B.D)
60
(T.B.D)
mA
High-level
input current
Low-level
input current
RESB, MODE, MODE3,
IIH
CE, CL, DI,
CONT00, CONT01, CONT02,
CONT03, CONT04, CONT05,
CONT08, CONT09, CONT10,
DO,
Schmitt
VIN=VDD
Built-in
Pull-down
Resistor
SDDAT00 to 15,
OFF
SDADRS11, SDADRS12
RESB, TEST, MODE3,
CE, CL, DI,
VIN=0.0V
CONT00, CONT01, CONT02,
Built-in
IIL CONT03, CONT04, CONT05, Schmitt Pull-down 10.00
CONT08, CONT09, CONT10,
Resistor
SDDAT00 to 15,
OFF
SDADRS11, SDADRS12
10.00
μA
High-level
output voltage
VOH(1)
DO, BUSYB,
CONT00, CONT01, CONT02,
CONT03, CONT05,
CONT08, CONT09, CONT10,
SDDAT00 to SDDAT15,
SDADRS00 to SDADRS12,
SDBA,
SDCKE, SDCSB, SDRASB,
SDCASB, SDWEB, SDDQM
CMOS IOH=2mA VDD
0.6
Low-level
output voltage
VOH(2)
VOL(1)
CL, DI, CONT04, SDCLK
DO, BUSYB,
CONT00, CONT01, CONT02,
CONT03, CONT05,
CONT08, CONT09, CONT10,
SDDAT00 to SDDAT15,
SDADRS00 to SDADRS12,
SDBA,
SDCKE, SDCSB, SDRASB,
SDCASB, SDWEB, SDDQM
CMOS IOH=4mA
CMOS IOL=2mA
V
0.40
VOL(2) CL, DI, CONT04, SDCLK
CMOS IOL=4mA
Output
off-leakage
current
IOFF(1) PDOUT0, PDOUT1
IOFF(2) DO
Hi-Z Out
Hi-Z Out
10.00
10.00
10.00
μA
10.00
Built-in
Pull-down
resistor
CE,
CONT00, CONT01, CONT02,
RPD
CONT03, CONT04, CONT05,
CONT08, CONT09, CONT10,
SDDAT00 to SDDAT15,
SDADRS11,SDADRS12
50
100
200 kΩ
Charge pump
output current
IPDOH PDOUT1, PDOUT0
IPDOL PDOUT1, PDOUT0
PCKIST=
100kΩ
35
50
65
Current
μA
value
65
50
35
Setting :1x
(Notes)
 Connect and use the pull-up or the pull-down resister with the outside when you use serial communications because the terminal
DO is 3- State output (initial state).
 The DO, BUSYB, CONT00, CONT01, CONT02, CONT03, CONT04, CONT05, CONT08, CONT09 and CONT10 pins can be
used as the N channel open drain pins. When used as the N channel open drain pin, external pull-upresistor must be connected to
those pins.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
4