CAT9532_16 Datasheet, PDF (4/14 Pages) ON Semiconductor – 16-bit Programmable LED Dimmer

CAT9532
Table 3. D.C. OPERATING CHARACTERISTICS (V_CC = 2.3 to 5.5 V, V_SS = 0 V; T_A = −40°C to +85°C, unless otherwise specified)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
SUPPLIES
V_CC
I_CC
I_stb
ΔI_stb
Supply Voltage
Supply Current
Standby Current
Additional Standby Current
Operating mode; V_CC = 5.5 V; no load;
f_SCL = 100 kHz
Standby mode; V_CC = 5.5 V; no load;
V_I = V_SS or V_CC, f_SCL = 0 kHz
Standby mode; V_CC = 5.5 V; every
LED I/O = V_IN = 4.3 V, f_SCL = 0 kHz
2.3
−
5.5
V
−
250
550
mA
−
2.1
5.0
mA
−
−
2
mA
V_POR (Note 1) Power−on Reset Voltage
V_CC = 3.3 V, No load;
V_I = V_CC or V_SS
−
1.5
2.2
V
SCL, SDA
V_IL (Note 2)
V_IH (Note 2)
I_OL
I_IL
C_I (Note 3)
C_O (Note 3)
A0, A1, A2
Low Level Input Voltage
High Level Input Voltage
Low Level Output Current
Leakage Current
Input Capacitance
Output Capacitance
V_OL = 0.4 V
V_I = V_CC = V_SS
V_I = V_SS
V_O = V_SS
−0.3
−
0.3 V_CC
V
0.7 V_CC
−
5.5
V
3
−
−
mA
−1
−
+1
mA
−
−
6
pF
−
−
8
pF
V_IL (Note 2)
V_IH (Note 2)
I_IL
I/Os
Low Level Input Voltage
High Level Input Voltage
Input Leakage Current
−0.3
−
0.8
V
2.0
−
5.5
V
−1
−
1
mA
V_IL (Note 2)
V_IH (Note 2)
I_OL (Note 4)
Low Level Input Voltage
High Level Input Voltage
Low Level Output Current
I_IL
C_I/O (Note 3)
RESET
Input Leakage Current
Input/Output Capacitance
V_OL = 0.4 V; V_CC = 2.3 V
V_OL = 0.4 V; V_CC = 3.0 V
V_OL = 0.4 V; V_CC = 5.0 V
V_OL = 0.7 V; V_CC = 2.3 V
V_OL = 0.7 V; V_CC = 3.0 V
V_OL = 0.7 V; V_CC = 5.0 V
V_CC = 3.6 V; V_I = V_SS or V_CC
−0.3
−
0.8
V
2.0
−
5.5
V
9
−
−
mA
12
−
−
15
−
−
15
−
−
20
−
−
25
−
−
−1
−
1
mA
−
−
8
pF
V_IL (Note 2) Low Level Input Voltage
−0.3
−
0.2 V_CC
V
V_IH (Note 2) High Level Input Voltage
0.7 V_CC
−
5.5
V
I_IL
Input Leakage Current
V_I = V_CC or V_SS
−1
−
1
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. V_CC must be lowered to 0.2 V in order to reset the device.
2. V_IL min and V_IH max are reference values only and are not tested.
3. This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested.
4. The output current must be limited to a maximum 25 mA per each I/O; the total current sunk by all I/O must be limited to 400 mA.
www.onsemi.com
4