NOIL1SM0300A Datasheet, PDF (3/31 Pages) ON Semiconductor – LUPA300 CMOS Image Sensor

NOIL1SM0300A
SPECIFICATIONS
GENERAL SPECIFICATIONS
Parameter
Specifications
Pixel Architecture
6 transistor pixel
Pixel Size
9.9 mm x 9.9 mm
Resolution
640 (H) x 480 (V)
Subsampling
subsampling is possible (only in the
Y-direction)
Sub-sampling pattern: Y0Y0Y0Y0
Windowing (ROI)
Randomly programmable ROI read out.
Implemented as scanning of lines/
columns from an uploaded position
Read out direction
Read out direction can be reversed in X
and Y
Programmable gain Range x1 to x16, in 16 steps using
4-bits programming
Programmable offset 256 steps (8 bit)
Digital output
On−chip 10−bit ADCs at 80
Msamples/s
Power dissipation
160 mW not including output load
190 mW with output load of 15 pF
Package type
48 pin LCC
Mass
±1 g
ELECTRO−OPTICAL SPECIFICATIONS
Parameter
Typical Specifications
Optical Format
½ optical inch
Shutter Type
Pipelined Global shutter
Frame Rate
250 fps
FPN
PRNU
Conversion gain
Saturation charge
2.5% RMS_p-p (Min: 10%, Max: 3.1%)
2.5% RMS, Max: 3.1%
34 uV/e^- at output
35.000 e^-
Sensitivity
3200 V.m2/W.s
17 V/lux.s (180 lux = 1 W/m²)
Peak QE * FF
45%
Dark current (at 21°C) 300 mV/s
Noise electrons
32e^-
S/N ratio
43 dB
Parasitic sensitivity
1/5000
Dynamic Range
61 dB
Extended dynamic
range
Multiple slope (up to 90 dB optical dy-
namic range)
MTF
60%
Table 1. RECOMMENDED OPERATING RATINGS (Notes 1 and 2)
Symbol
Parameter
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _TJ
Operating temperature range
Min
Max
Units
−40
70
°C
Table 2. ABSOLUTE MAXIMUM RATINGS (Notes 2, 3 and 4)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VDD[5]
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _TS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _%RH
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{ESD[3] & LU[4]}
DC Supply Voltage
Storage Temperature
Humidity (Relative)
ESD & Latch−up
Parameter
Min
Max
−0.5
4.3
−30
+85
−
85% at 85°C
(Notes 3 and 4)
Units
V
°C
mA
1. Operating ratings are conditions in which operation of the device is intended to be functional. All parameters are characterized for DC
conditions after thermal equilibrium is established. Unused inputs must always be tied to an appropriate logic level, for example, VDD or GND.
2. Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified
is not implied.
3. This device does NOT contain circuitry to protect the inputs against damage caused by high static voltages or electric fields.
ON Semiconductor recommends that customers become familiar with, and follow the procedures in JEDEC Standard JESD625−A. Refer
to Application Note AN52561.
4. The LUPA300 does not have latchup protection.
5. V_DD = V_DDD = V_DDA (V_DDD is supply to digital circuit, V_DDA to analog circuit).
http://onsemi.com
3