|
MC74LVXT8051_05 Datasheet, PDF (3/12 Pages) ON Semiconductor – Analog Multiplexer / Demultiplexer High−Performance Silicon−Gate CMOS | |||
|
◁ |
MC74LVXT8051
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ MAXIMUM RATINGS
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
Parameter
Value
Unit
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VCC Positive DC Supply Voltage (Referenced to GND) â 0.5 to + 7.0
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIS Analog Input Voltage
â 0.5 to VCC + 0.5 V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Vin Digital Input Voltage (Referenced to GND)
â 0.5 to VCC + 0.5 V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ I
DC Current, Into or Out of Any Pin
â20
mA
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ PD Power Dissipation in Still Air,
SOIC Packageâ
500
mW
TSSOP Packageâ
450
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Tstg Storage Temperature Range
â 65 to + 150
_C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ TL Lead Temperature, 1 mm from Case for 10 Seconds
260
_C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Maximum ratings are those values beyond which device damage can occur. Maximum ratings
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ applied to the device are individual stress limit values (not normal operating conditions) and are
not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
â Derating â SOIC Package: â 7 mW/_C from 65_ to 125_C
TSSOP Package: â 6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
Parameter
Min
Max Unit
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VCC Positive DC Supply Voltage (Referenced to GND) 2.0
6.0
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIS Analog Input Voltage
0.0
VCC
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Vin Digital Input Voltage (Referenced to GND)
GND
VCC
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIO* Static or Dynamic Voltage Across Switch
1.2
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ TA Operating Temperature Range, All Package Types
â 55
+ 85 _C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ tr, tf Input Rise/Fall Time
(Channel Select or Enable Inputs)
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃà VCC = 3.3 V ± 0.3 V
0
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃà VCC = 5.0 V ± 0.5 V
0
ns/V
100
20
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ *For voltage drops across switch greater than 1.2 V (switch on), excessive VCC current may be
drawn; i.e., the current out of the switch may contain both VCC and switch input components. The
reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this highâimpedance cir-
cuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
DC CHARACTERISTICS â Digital Section (Voltages Referenced to GND)
Symbol
Parameter
VIH Minimum HighâLevel Input Voltage,
ChannelâSelect or Enable Inputs
Condition
Ron = Per Spec
VIL Maximum LowâLevel Input Voltage, Ron = Per Spec
ChannelâSelect or Enable Inputs
Iin
Maximum Input Leakage Current,
ChannelâSelect or Enable Inputs
ICC Maximum Quiescent Supply
Current (per Package)
Vin = VCC or GND
Channel Select, Enable and
VIS = VCC or GND; VIO = 0 V
Guaranteed Limit
VCC
V â55 to 25°C â¤85°C â¤125°C Unit
3.0
1.2
4.5
2.0
5.5
2.0
1.2
1.2
V
2.0
2.0
2.0
2.0
3.0
0.53
0.53 0.53
V
4.5
0.8
0.8
0.8
5.5
0.8
0.8
0.8
5.5
± 0.1
± 1.0 ± 1.0
mA
5.5
4
40
160
mA
http://onsemi.com
3
|
▷ |