MC74LCX541_14 Datasheet, PDF (3/8 Pages) ON Semiconductor – Low-Voltage CMOS Octal Buffer Flow Through Pinout

MC74LCX541
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Typ
Max
Units
V_CC Supply Voltage
Operating
Data Retention Only
V
2.0
3.3
3.6
1.5
3.3
3.6
V_I
Input Voltage
V_O Output Voltage
(HIGH or LOW State)
(3−State)
0
5.5
V
V
0
V_CC
0
5.5
I_OH HIGH Level Output Current, V_CC = 3.0 V − 3.6 V
−24
mA
I_OL LOW Level Output Current, V_CC = 3.0 V − 3.6 V
24
mA
I_OH HIGH Level Output Current, V_CC = 2.7 V − 3.0 V
−12
mA
I_OL LOW Level Output Current, V_CC = 2.7 V − 3.0 V
12
mA
T_A
Operating Free−Air Temperature
−40
+85
°C
Dt/DV Input Transition Rise or Fall Rate, V_IN from 0.8 V to 2.0 V, V_CC = 3.0 V
0
10
ns/V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
T_A = −40°C to +85°C
Symbol
Characteristic
Condition
Min
Max
Units
V_IH HIGH Level Input Voltage (Note 2)
V_IL LOW Level Input Voltage (Note 2)
V_OH HIGH Level Output Voltage
V_OL LOW Level Output Voltage
I_OZ 3−State Output Current
2.7 V ≤ V_CC ≤ 3.6 V
2.7 V ≤ V_CC ≤ 3.6 V
2.7 V ≤ V_CC ≤ 3.6 V; I_OH = −100 mA
V_CC = 2.7 V; I_OH = −12 mA
V_CC = 3.0 V; I_OH = −18 mA
V_CC = 3.0 V; I_OH = −24 mA
2.7 V ≤ V_CC ≤ 3.6 V; I_OL = 100 mA
V_CC = 2.7 V; I_OL = 12 mA
V_CC = 3.0 V; I_OL = 16 mA
V_CC = 3.0 V; I_OL = 24 mA
V_CC = 3.6 V, V_IN = V_IH or V_IL,
V_OUT = 0 to 5.5 V
2.0
V
0.8
V
V_CC − 0.2
V
2.2
2.4
2.2
0.2
V
0.4
0.4
0.55
±5
mA
I_OFF Power Off Leakage Current
V_CC = 0, V_IN = 5.5 V or V_OUT = 5.5 V
10
mA
I_IN
Input Leakage Current
V_CC = 3.6 V, V_IN = 5.5 V or GND
±5
mA
I_CC Quiescent Supply Current
V_CC = 3.6 V, V_IN = 5.5 V or GND
10
mA
DI_CC Increase in I_CC per Input
2.3 ≤ V_CC ≤ 3.6 V; V_IH = V_CC − 0.6 V
500
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. These values of V_I are used to test DC electrical characteristics only.
http://onsemi.com
3