MC74LCX08_14 Datasheet, PDF (3/7 Pages) ON Semiconductor – Low-Voltage CMOS Quad 2-Input AND Gate

MC74LCX08
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Type
Max
Unit
V_CC
Supply Voltage
Operating
Data Retention Only
2.0
2.5, 3.3
3.6
V
1.5
2.5, 3.3
3.6
V_I
Input Voltage
V_O
Output Voltage
0
(HIGH or LOW State)
0
(3−State)
5.5
V
V_CC
V
I_OH
HIGH Level Output Current
V_CC = 3.0 V − 3.6 V
V_CC = 2.7 V − 3.0 V
V_CC = 2.3 V − 2.7 V
−24
mA
−12
−8
I_OL
LOW Level Output Current
V_CC = 3.0 V − 3.6 V
V_CC = 2.7 V − 3.0 V
V_CC = 2.3 V − 2.7 V
+24
mA
+12
+8
T_A
Operating Free−Air Temperature
−40
+85
°C
Dt/DV
Input Transition Rise or Fall Rate, V_IN from 0.8 V to 2.0 V, V_CC = 3.0 V
0
10
ns/V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
T_A = −40°C to +85°C
Symbol
Characteristic
Condition
Min
Max
Unit
V_IH
HIGH Level Input Voltage (Note 2)
V_IL
LOW Level Input Voltage (Note 2)
V_OH
HIGH Level Output Voltage
2.3 V ≤ V_CC ≤ 2.7 V
1.7
V
2.7 V ≤ V_CC ≤ 3.6 V
2.0
2.3 V ≤ V_CC ≤ 2.7 V
0.7
V
2.7 V ≤ V_CC ≤ 3.6 V
0.8
2.3 V ≤ V_CC ≤ 3.6 V; I_OH = −100 mA
V_CC − 0.2
V
V_CC = 2.3 V; I_OH = −8 mA
1.8
V_CC = 2.7 V; I_OH = −12 mA
2.2
V_CC = 3.0 V; I_OH = −18 mA
2.4
V_OL
LOW Level Output Voltage
V_CC = 3.0 V; I_OH = −24 mA
2.3 V ≤ V_CC ≤ 3.6 V; I_OL = 100 mA
V_CC = 2.3 V; I_OL = 8 mA
V_CC = 2.7 V; I_OL = 12 mA
2.2
0.2
V
0.6
0.4
V_CC = 3.0 V; I_OL = 16 mA
0.4
V_CC = 3.0 V; I_OL = 24 mA
0.55
I_OFF
Power Off Leakage Current
V_CC = 0, V_IN = 5.5 V or V_OUT = 5.5 V
10
mA
I_IN
Input Leakage Current
V_CC = 3.6 V, V_IN = 5.5 V or GND
±5
mA
I_CC
Quiescent Supply Current
V_CC = 3.6 V, V_IN = 5.5 V or GND
10
mA
DI_CC
Increase in I_CC per Input
2.3 ≤ V_CC ≤ 3.6 V; V_IH = V_CC − 0.6 V
500
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. These values of V_I are used to test DC electrical characteristics only.
http://onsemi.com
3