CM1263-06DE_13 Datasheet, PDF (3/4 Pages) ON Semiconductor – Low Capacitance ESD Protection for High-Speed Serial Interfaces

CM1263−06DE
SPECIFICATIONS
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameter
Rating
Units
Operating Supply Voltage (V_P − V_N)
Operating Temperature Range
6.0
V
−40 to +85
°C
Storage Temperature Range
−65 to +150
°C
DC Voltage at any channel input
(V_N − 0.5) to (V_P + 0.5)
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 3. ELECTRICAL OPERATING CHARACTERISTICS (Note 1)
Symbol
Parameter
Conditions
V_P
Operating Supply Voltage (V_P−V_N)
I_P
Operating Supply Current
V_F
Diode Forward Voltage
Top Diode
Bottom Diode
V_P = 3.3 V, V_N = 0 V (per V_P pin)
T_A = 25°C, I_F = 8 mA, V_P = 3.3 V,
V_N = 0 V
I_LEAK
Channel Leakage Current
T_A = 25°C; V_P = 3.3 V, V_N = 0 V
(Channel 1)
V_P = 3.3 V, V_N = 0 V
(Channels 1−6)
I_R
Reverse (Leakage Current)
V_P = floating; V_N = 0 V
(per channel)
C_IN
Channel Input Capacitance
DC_IN
Channel Input Capacitance Matching
C_MUTUAL
V_ESD
Mutual Capacitance between signal pin
and adjacent signal pin
ESD Protection
Peak Discharge Voltage at any channel
input, in system
a) Contact discharge per
IEC 61000−4−2 standard
b) Air discharge per
IEC 61000−4−2 standard
At 1 MHz, V_P = 3.3 V, V_N = 0 V,
V_IN = 0 V
At 1 MHz, V_P = 3.3 V, V_N = 0 V,
V_IN = 0 V
At 1 MHz, V_P = 3.3 V, V_N = 0 V,
V_IN = 0 V
T_A = 25°C (Notes 2 and 3)
V_CL
Channel Clamp Voltage
Positive Transients
Negative Transients
T_A = 25°C, I_PP = 1 A, t_P = 8/20 mS
(Note 3)
R_DYN
Dynamic Resistance
Positive Transients
Negative Transients
T_A = 25°C, I_PP = 1 A, t_P = 8/20 mS
Any I/O pin to Ground (Note 3)
1. All parameters specified at T_A = –40°C to +85°C unless otherwise noted.
2. Standard IEC 61000−4−2 with C_Discharge = 150 pF, R_Discharge = 330 W, V_P = 3.3 V, V_N grounded.
3. These measurements performed with no external capacitor on V_P (V_P floating).
Min Typ Max Units
3.3 5.5
V
8.0 mA
V
0.60 0.80 0.95
0.60 0.80 0.95
250 nA
1000 nA
1000 nA
0.88 1.2 pF
0.02
pF
0.11
pF
kV
±8
±15
V
+9.96
–1.6
W
0.96
0.5
http://onsemi.com
3