CAT25M02_16 Datasheet, PDF (3/14 Pages) ON Semiconductor – 2 Mb SPI Serial CMOS EEPROM

CAT25M02
Table 3. D. C. OPERATING CHARACTERISTICS
(V_CC = 1.7 V to 5.5 V, T_A = −40°C to +85°C and V_CC = 2.5 V to 5.5 V, T_A = −40°C to +125°C, unless otherwise specified)
Symbol
Parameter
Test Conditions
Min
Max
Units
I_CCR
I_CCW
Supply Current
(Read Mode)
Read, SO open /
−40°C to +85°C
Supply Current
(Write Mode)
Read, SO open /
−40°C to +125°C
Write, CS = V_CC/
−40°C to +85°C
V_CC = 1.7 V, f_SCK = 5 MHz
V_CC = 2.5 V, f_SCK = 10 MHz
V_CC = 5.5 V, f_SCK = 10 MHz
2.5 V < V_CC < 5.5 V,
f_SCK = 10 MHz
1.7 V < V_CC < 5.5 V
1.2
mA
1.6
mA
2
mA
2
mA
2
mA
Write, CS = V_CC/
−40°C to +125°C
2.5 V < V_CC < 5.5 V
2
mA
I_SB1
(Note 5)
Standby Current
V_IN = GND or V_CC,
CS = V_CC, WP = V_CC,
HOLD = V_CC,
V_CC = 5.5 V
T_A = −40°C to +85°C
T_A = −40°C to +125°C
2
mA
4
mA
I_SB2
(Note 5)
Standby Current
V_IN = GND or V_CC,
CS = V_CC, WP = GND,
HOLD = GND,
V_CC = 5.5 V
T_A = −40°C to +85°C
T_A = −40°C to +125°C
3
mA
5
mA
I_L
Input Leakage Current V_IN = GND or V_CC
−2
2
mA
I_LO
Output Leakage
CS = V_CC
Current
V_OUT = GND or V_CC
−2
2
mA
V_IL1
Input Low Voltage
V_CC ≥ 2.5 V
−0.5
0.3V_CC
V
V_IH1
Input High Voltage
V_CC ≥ 2.5 V
0.7V_CC
V_CC + 0.5
V
V_IL2
Input Low Voltage
V_CC < 2.5 V
−0.5
0.25V_CC
V
V_IH2
Input High Voltage
V_CC < 2.5 V
0.75V_CC
V_CC + 0.5
V
V_OL1
Output Low Voltage
V_CC ≥ 2.5 V, I_OL = 3.0 mA
0.4
V
V_OH1
Output High Voltage
V_CC ≥ 2.5 V, I_OH = −1.6 mA
V_CC − 0.8V
V
V_OL2
Output Low Voltage
V_CC < 2.5 V, I_OL = 150 mA
0.2
V
V_OH2
Output High Voltage
V_CC < 2.5 V, I_OH = −100 mA
V_CC − 0.2V
V
5. When not driven, the WP and HOLD inputs are pulled up to V_CC internally. For noisy environments, when the pin is not used, it is
recommended the WP and HOLD input to be tied to V_CC, either directly or through a resistor.
www.onsemi.com
3