LB11696V Datasheet, PDF (2/17 Pages) Sanyo Semicon Device – Direct PWM Drive Brushless Motor Predriver IC

LB11696V
Allowable Operating Ranges at Ta = 25 C
Parameter
Supply voltage range 1-1
Supply voltage range 1-2
Output current
5 V constant voltage output current
HP pin applied voltage
HP pin output current
RD pin applied voltage
RD pin output current
Symbol
V_CC1-1
V_CC1-2
I_O
IREG
VHP
IHP
VRD
IRD
Conditions
V_CC pin
V_CC pin, when V_CC is shorted to VREG.
UL, VL, WL, UH, VH, and WH pins
Ratings
Unit
8 to 17
V
4.5 to 5.5
V
25
mA
0 to 17
V
0 to 15
mA
0 to 17
V
0 to 15
mA
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
Electrical Characteristics at Ta = 25 C, V_CC = 12 V
Parameter
Symbol
Current drain 1
Current drain 2
[5 V Constant Voltage Output (VREG pin)]
Output voltage
Line regulation
Load regulation
Temperature coefficient
[Output Block]
Output voltage 1-1
Output voltage 1-2
Output voltage 2
Output leakage current
[Hall Amplifier Block]
Input bias current
I_CC1
I_CC2
VREG
ΔVREG1 V
ΔVREG2 I
Δ
V_OUT
V_OUT
V_OUT
I_Oleak
IHB (HA)
Ratings
min
typ
max
Unit
12
16 mA
2.5
4 mA
4.7
5.0
5.3
V
40
100 mV
10
30 mV
0
Common-mode input voltage range 2
VICM2
Hall Input Sensitivity
Hysteresis
Input voltage low → high
Input voltage high → low
[CTL Amplifier]
Input offset voltage
Input bias current
Common-mode input voltage range
High-level output voltage
Low-level output voltage
Open-loop gain
[PWM Oscillator (PWM pin)]
High-level output voltage
Low-level output voltage
External capacitor charge current
Oscillator frequency
Amplitude
[TOC pin]
Input voltage 1
Input voltage 2
Input voltage 1 low
Input voltage 2 low
Input voltage 1 high
Input voltage 2 high
[HP Pin]
Output saturation voltage
Output leakage current
ΔVIN (HA)
VSLH (HA)
VSHL (HA)
V_IO (CTL)
I_B (CTL)
VICM
V_OH
V_OL
V_OH (PWM)
V_OL (PWM)
ICHG
f (PWM)
V (PWM)
VPWM = 2.1 V
C = 2000 pF
VTOC1 Output duty: 100%
2.68
3.0
3.34
V
VTOC2 Output duty: 0%
1.2
1.35
1.5
V
VTOC1L Design target value, when VREG = 4.7 V, 100%
2.68
2.82
2.96
V
VTOC2L Design target value, when VREG = 4.7 V, 0%
1.23
1.29
1.34
V
VTOC1H Design target value, when VREG = 5.3 V, 100%
3.02
3.18
3.34
V
VTOC2H Design target value, when VREG = 5.3 V, 0%
1.37
1.44
1.50
V
VHPL
IHPleak
I_O = 10 mA
V_O = 18 V
0.2
0.5
V
10 μA
Continued on next page.
www.onsemi.com
2