E2EQ Datasheet, PDF (3/8 Pages) Omron Electronics LLC – A Series of Spatter-resistant Proximity Sensors with a Teflon-coated Metal Housing

Standard
Item
Sensing distance
Model
E2EQ-X3D1
E2EQ-X3D1-M1GJ
3 mm ±10%
E2EQ-X7D1
E2EQ-X7D1-M1GJ
7 mm ±10%
E2EQ-X10D1
E2EQ-X10D1-M1GJ
10 mm ±10%
Setting distance
0 to 2.4 mm
0 to 5.6 mm
0 to 8 mm
Differential distance
10% max.
Standard sensing object
(mild steel)
12 x 12 x 1 mm
18 x 18 x 1 mm
30 x 30 x 1 mm
Response frequency
Control out-
put
Switching
capacity
Residual
voltage
1 kHz
3 to 100 mA
500 Hz
400 Hz
3.0 V max. (under load current of 100 mA with cable length of 2 m)
Operating status (with
sensing object approaching)
NO
Protective circuits
Surge absorber, short-circuit protection
Ambient temperature
Operating/Storage: -25°C to 70°C (with no icing or condensation)
Temperature influence
±10% max. of sensing distance at 23°C within temperature range of -25°C and 70°C
Voltage influence
±2.5% max. of Sensing distance within rated voltage range ±15%.
Shock resistance
Destruction: 1,000 m/s² for 10 times each in X, Y, and Z directions
Connection method
E2EQ-X#D1: Pre-wired models (Standard length: 2 m)
E2EQ-X#D1-M1GJ type: Connector relay models (Standard length: 300 mm)
Weight
(Packed
state)
Pre-wired
Junction
connector
Approx. 120 g
Approx. 80 g
Approx. 160 g
Approx. 110 g
Approx. 220 g
Approx. 190 g
* The response frequencies for DC switching are average values measured on condition that the distance between each sensing object is twice as large as the size
of the sensing object and the sensing distance set is half of the maximum sensing distance.
General
Model
E2EQ-X4X1
E2EQ-X8X1
E2EQ-X15X1
E2EQ-X4X1-M1J
E2EQ-X8X1-M1J
E2EQ-X15X1-M1J
E2EQ-X3D1
E2EQ-X7D1
E2EQ-X10D1
Item
E2EQ-X3D1-M1GJ
E2EQ-X7D1-M1GJ
E2EQ-X10D1-M1GJ
Sensing object
Ferrous metal (Sensitivity lowers with non-ferrous metals)
Rated supply voltage (operat-
ing voltage)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Leakage current
0.8 mA max.
Indicator lamp
Operation indicator (red), operation setting indicator (green)
Ambient humidity
Operating/Storage: 35% to 95%RH (with no condensation)
Insulation resistance
50 MW min. (at 500 VDC) between energized parts and case
Dielectric strength
1,000 VAC for 1 min between energized parts and case
Vibration resistance
10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Protective structure
IEC60529 IP67
Material
Case
Teflon resin coating (base: brass) *
Sensing surface Teflon resin *
Accessories
Instruction manual
* Teflon is a registered trademark of Dupont Company and Mitsui Dupont Chemical Company for their fluoride resin.
E-34
Proximity Sensors