ISP1504A1_07 Datasheet, PDF (59/81 Pages) NXP Semiconductors – ULPI Hi-Speed Universal Serial Bus On-The-Go transceiver

NXP Semiconductors
ISP1504A1; ISP1504C1
ULPI HS USB OTG transceiver
Table 47. Static characteristics: digital pins CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N, CS_N/PWRDN …continued
V_CC = 3.0 V to 4.5 V; V_CC(I/O) = 1.65 V to 3.6 V; T_amb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at V_CC = 3.6 V; V_CC(I/O) = 1.8 V; T_amb = +25 °C; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Pull-up and pull-down
I_pd
pull-down current
I_pu
pull-up current
interface protect enabled;
25
50
90
µA
DATA[7:0] pins only; V_I =
V_CC(I/O)
interface protect enabled;
−30
−50
−80
µA
STP pin only; V_I = 0 V
Capacitance
C_in
input capacitance
-
-
3.5
pF
Table 48. Static characteristics: digital pin FAULT
V_CC = 3.0 V to 4.5 V; V_CC(I/O) = 1.65 V to 3.6 V; T_amb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at V_CC = 3.6 V; V_CC(I/O) = 1.8 V; T_amb = +25 °C; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Input levels
V_IL
LOW-level input voltage
V_IH
HIGH-level input voltage
I_IL
LOW-level input current V_I = 0 V
I_IH
HIGH-level input current V_I = V_CC(I/O)
-
-
2.0
-
-
-
-
-
0.8
V
-
V
1
µA
1
µA
Table 49. Static characteristics: digital pin PSW_N
V_CC = 3.0 V to 4.5 V; V_CC(I/O) = 1.65 V to 3.6 V; T_amb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at V_CC = 3.6 V; V_CC(I/O) = 1.8 V; T_amb = +25 °C; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Output levels
V_OH
HIGH-level output voltage external pull-up resistor connected
V_OL
LOW-level output voltage I_OL = −4 mA
I_OH
HIGH-level output current external pull-up resistor connected
I_OL
LOW-level output current V_O = 0.4 V
3.0^[1]
-
-
-
-
-
4.0
-
[1] When V_OH is less than 3.0 V, I_CC may increase because of the cross current.
Max
5.25
0.4
1
-
Unit
V
V
µA
mA
Table 50. Static characteristics: analog I/O pins DP, DM
V_CC = 3.0 V to 4.5 V; V_CC(I/O) = 1.65 V to 3.6 V; T_amb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at V_CC = 3.6 V; V_CC(I/O) = 1.8 V; T_amb = +25 °C; unless otherwise specified.
Symbol Parameter
Conditions
Min Typ
Original USB transceiver (low-speed and full-speed)
Input levels (differential receiver)
V_DI
differential input sensitivity
|V_DP − V_DM|
0.2
-
V_CM
differential common mode voltage range
includes V_DI range
0.8
-
Input levels (single-ended receivers)
V_IL
LOW-level input voltage
-
-
V_IH
HIGH-level input voltage
2.0
-
Max
-
2.5
0.8
-
Unit
V
V
V
V
ISP1504A1_ISP1504C1_1
Product data sheet
Rev. 01 — 6 August 2007
© NXP B.V. 2007. All rights reserved.
58 of 80