AD8099_13 Datasheet, PDF (5/29 Pages) Analog Devices – Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp

AD8099
Data Sheet
SPECIFICATIONS WITH +5 V SUPPLY
VS = 5 V @ TA = 25°C, G = +2, RL = 1 kΩ to midsupply, unless otherwise noted. Refer to Figure 60 through Figure 66 for component
values and gain configurations .
Table 2.
Parameter
Conditions
Min
Typ
Max Unit
DYNAMIC PERFORMANCE
–3 dB Bandwidth
Bandwidth for 0.1 dB Flatness (SOIC/LFCSP)
Slew Rate
Settling Time to 0.1%
G = +5, VOUT = 0.2 V p-p
G = +5, VOUT = 2 V p-p
G = +2, VOUT = 0.2 V p-p
G = +10, VOUT = 2 V Step
G = +2, VOUT = 2 V Step
G = +2, VOUT = 2 V Step
415
440
MHz
165
210
MHz
33/23
MHz
630
715
V/µs
340
365
V/µs
18
ns
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion (dBc) HD2/HD3
Input Voltage Noise
fC = 500 kHz, VOUT = 1 V p-p, G = +10
fC = 10 MHz, VOUT = 1 V p-p, G = +10
f = 100 kHz
–82/–94
–80/–75
0.95
dBc
dBc
nV/√Hz
Input Current Noise
f = 100 kHz, DISABLE pin floating
2.6
pA/√Hz
f = 100 kHz, DISABLE pin = +VS
5.2
pA/√Hz
DC PERFORMANCE
Input Offset Voltage
0.1
0.5 mV
Input Offset Voltage Drift
2.5
µV/°C
Input Bias Current
DISABLE pin floating
–6.2
–13 µA
DISABLE pin = +VS
–0.2
–2 µA
Input Bias Offset Current
0.05
1 µA
Input Bias Offset Current Drift
2.4
nA/°C
Open-Loop Gain
INPUT CHARACTERISTICS
VOUT = 1 V to 4 V
76
81
dB
Input Resistance
Differential mode
4
kΩ
Common mode
10
MΩ
Input Capacitance
2
pF
Input Common-Mode Voltage Range
1.3 to 3.7
V
Common-Mode Rejection Ratio
VCM = 2 V to 3 V
88
105
dB
DISABLE PIN
DISABLE Input Voltage
Output disabled
<2.4
V
Turn-Off Time
Turn-On Time
Enable Pin Leakage Current
50% of DISABLE to <10% of Final VOUT,
VIN = 0.5 V, G = +2
50% of DISABLE to <10% of Final VOUT,
VIN = 0.5 V, G = +2
DISABLE = 5 V
105
ns
61
ns
16
21 µA
DISABLE Pin Leakage Current
DISABLE = 0 V
33
44 µA
OUTPUT CHARACTERISTICS
Overdrive Recovery Time (Rise/Fall)
Output Voltage Swing
Short-Circuit Current
VIN = 0 to 2.5 V, G = +2
RL = 100 Ω
RL = 1 kΩ
Sinking and Sourcing
50/70
ns
1.5 to 3.5 1.2 to 3.8
V
1.2 to 3.8 1.2 to 3.8
V
60/80
mA
Off Isolation
f = 1 MHz, DISABLE = Low
–61
dB
POWER SUPPLY
Operating Range
±5
±6 V
Quiescent Current
14.5
15.4 mA
Quiescent Current (Disabled)
DISABLE = Low
1.4
1.7 mA
Positive Power Supply Rejection Ratio
+VS = 4.5 V to 5.5 V, –VS = 0 V (input referred)
84
89
dB
Negative Power Supply Rejection Ratio
+VS =5 V, -VS= –0.5 V to +0.5 V (input referred)
84
90
dB
Rev. D | Page 4 of 28