UJA1078 Datasheet, PDF (34/53 Pages) NXP Semiconductors – High-speed CAN/dual LIN core system basis chip

NXP Semiconductors
UJA1078
High-speed CAN/dual LIN core system basis chip
Table 10. Static characteristics …continued
T_vj = −40 °C to +150 °C; V_BAT = 4.5 V to 28 V; V_BAT > V_V1; V_BAT > V_V2; R_LIN1 = R_LIN2 = 500 Ω; R_(CANH-CANL) = 45 Ω to 65 Ω; all
voltages are defined with respect to ground; positive currents flow in the IC; typical values are given at V_BAT = 14 V; unless
otherwise specified.
Symbol
Parameter
Conditions
Min Typ Max Unit
Voltage source; pin V1
V_O
R_(BAT-V1)
output voltage
resistance between pin BAT
and pin V1
V_O(V1)nom = 5 V; V_BAT = 5.5 V to 28 V
I_V1 = −200 mA to −5 mA
C_LIN1/2 ≥ 560 pF
V_O(V1)nom = 5 V; V_BAT = 5.5 V to 28 V
I_V1 = −200 mA to −5 mA
C_LIN1/2 ≥ 220 pF
V_O(V1)nom = 5 V; V_BAT = 5.5 V to 28 V
I_V1 = −250 mA to −200 mA
V_O(V1)nom = 5 V; V_BAT = 5.5 V to 5.75 V
I_V1 = −250 mA to −5 mA
150 °C < T_vj < 200 °C
V_O(V1)nom = 5 V; V_BAT = 5.75 V to 28 V
I_V1 = −250 mA to −5 mA
150 °C < T_vj < 200 °C
V_O(V1)nom = 3.3 V; V_BAT = 4.5 V to 28 V
I_V1 = −250 mA to −5 mA
C_LIN1/2 ≥ 560 pF
V_O(V1)nom = 3.3 V; V_BAT = 4.5 V to 28 V
I_V1 = −250 mA to −5 mA
C_LIN1/2 ≥ 220 pF
V_O(V1)nom = 3.3 V; V_BAT = 4.5 V to 28 V
I_V1 = −250 mA to −5 mA
150 °C < T_vj < 200 °C
V_O(V1)nom = 5 V; V_BAT = 4.5 V to 5.5 V
I_V1 = −250 mA to −5 mA
regulator in saturation
4.9 5
5.1
V
4.85 5
5.15 V
4.75 5
4.5 5
5.1
V
5.1
V
4.85 5
5.1
V
3.234 3.3 3.366 V
3.201 3.3 3.399 V
2.97 3.3 3.366 V
-
-
3
Ω
V_uvd
undervoltage detection
voltage
V_uvr
undervoltage recovery
voltage
I_O(sc)
short-circuit output current
Load regulation
90 %; V_O(V1)nom = 5 V; RTHC = 0
90 %; V_O(V1)nom = 3.3 V; RTHC = 0
70 %; V_O(V1)nom = 5 V; RTHC = 1
90 %; V_O(V1)nom = 5 V
90 %; V_O(V1)nom = 3.3 V
I_VEXCC = 0 mA
4.5 -
2.97 -
3.5 -
4.56 -
3.025 -
−600 -
4.75 V
3.135 V
3.75 V
4.9
V
3.234 V
−250 mA
ΔV_V1
voltage variation on pin V1 as a function of load current variation
-
-
25
mV
V_BAT = 5.75 V to 28 V
I_V1 = −250 mA to −5 mA
Line regulation
ΔV_V1
voltage variation on pin V1 as a function of supply voltage variation
-
-
25
mV
V_BAT = 5.5 V to 28 V; I_V1 = −30 mA
PNP base; pin VEXCTRL
I_O(sc)
short-circuit output current V_VEXCTRL ≥ 4.5 V; V_BAT = 6 V to 28 V
3.5 5.8 8
mA
UJA1078_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 27 May 2010
© NXP B.V. 2010. All rights reserved.
34 of 53