|
ADC12130 Datasheet, PDF (6/41 Pages) National Semiconductor (TI) – Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold | |||
|
◁ |
Converter Electrical Characteristics
The following specifications apply for
common-mode voltage) or (V+ = VA+
(V+ = VA+ = VD+ = +5V, VREF+ = +4.096V, and fully differential input with
= VD+ = 3.3V, VREF+ = +2.5V and fully-differential input with fixed 1.250V
fixed
2.048V
common-mode voltage), VREFâ = 0V, 12-bit + sign conversion mode, source impedance for analog inputs, VREFâ and VREF+
⤠25â¦, fCK = fSK = 5 MHz, and 10 (tCK) acquisition time unless otherwise specified. Boldface limits apply for TA = TJ =
TMIN to TMAX; all other limits TA = TJ = 25ËC. (Notes 7, 8, 9) (Continued)
Symbol
Parameter
Conditions
Typical
(Note 10)
Limits
Units
(Note 11) (Limits)
STATIC CONVERTER CHARACTERISTICS (Continued)
Multiplexer Channel to Channel
±0.05
LSB
Matching
Power Supply Sensitivity
V+ = +5V ±10%
Offset Error
VREF = +4.096V
±0.5
LSB
+ Full-Scale Error
±0.5
LSB
â Full-Scale Error
±0.5
LSB
+ Integral Linearity Error
±0.5
LSB
â Integral Linearity Error
±0.5
LSB
UNIPOLAR DYNAMIC CONVERTER CHARACTERISTICS
S/(N+D) Signal-to-Noise Plus
fIN = 1 kHz, VIN = 5 VPP, VREF+ = 5.0V
69.4
dB
Distortion Ratio
fIN = 20 kHz, VIN = 5 VPP, VREF+ = 5.0V
68.3
dB
fIN = 40 kHz, VIN = 5 VPP, VREF+ = 5.0V
65.7
dB
â3 dB Full Power Bandwidth
VIN = 5 VPP, where S/(N+D) drops 3 dB
31
kHz
DIFFERENTIAL DYNAMIC CONVERTER CHARACTERISTICS
S/(N+D) Signal-to-Noise Plus
fIN = 1 kHz, VIN = ±5V, VREF+ = 5.0V
77.0
dB
Distortion Ratio
fIN = 20 kHz, VIN = ±5V, VREF+ = 5.0V
73.9
dB
fIN = 40 kHz, VIN = ±5V, VREF+ = 5.0V
67.0
dB
â3 dB Full Power Bandwidth
VIN = ±5V, where S/(N+D) drops 3 dB
40
kHz
Electrical Characteristics
The following specifications apply for
common-mode voltage) or (V+ = VA+
(V+ = VA+ = VD+ = +5V, VREF+ = +4.096V, and fully differential input with
= VD+ = +3.3V, VREF+ = 2.5V and fully-differential input with fixed 1.250V
fixed
2.048V
common-mode voltage), VREFâ = 0V, 12-bit + sign conversion mode, source impedance for analog inputs, VREFâ and VREF+
⤠25â¦, fCK = fSK = 5 MHz, and 10 (tCK) acquisition time unless otherwise specified. Boldface limits apply for TA = TJ =
TMIN to TMAX; all other limits TA = TJ = 25ËC. (Notes 7, 8, 9)
Symbol
Parameter
Conditions
Typical
Limits
Units
(Note 10)
(Note 11)
(Limits)
REFERENCE INPUT, ANALOG INPUTS AND MULTIPLEXER CHARACTERISTICS
CREF
CA/D
Reference Input Capacitance
A/DIN1 and A/DIN2 Analog Input
Capacitance
85
pF
75
pF
A/DIN1 and A/DIN2 Analog Input
VIN = +5.0V or
±0.1
µA
Leakage Current
VIN = 0V
CH0âCH7 and COM Input Voltage
GND â 0.05
V
CCH
CH0âCH7 and COM Input
Capacitance
VA+ + 0.05
10
pF
CMUXOUT MUX Output Capacitance
20
pF
Off Channel Leakage (Note 16)
On Channel = 5V and
â0.01
µA
CH0âCH7 and COM Pins
Off Channel = 0V
On Channel = 0V and
0.01
µA
Off Channel = 5V
www.national.com
6
|
▷ |