LMH6645 Datasheet, PDF (5/28 Pages) National Semiconductor (TI) – 2.7V, 650μA, 55MHz, Rail-to-Rail Input and Output Amplifiers with Shutdown Option

LMH6645, LMH6646, LMH6647
www.ti.com
SNOS970C – JUNE 2001 – REVISED APRIL 2013
5V Electrical Characteristics (continued)
Unless otherwise specified, all limits guaranteed for at T_J = 25°C, V⁺ = 5V, V^− = 0V, V_CM = V_O = V⁺/2, and R_f = 2kΩ, and R_L =
1kΩ to V⁺/2. Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
(1)
(2)
(1)
CMVR
Input Common-Mode Voltage
Range
CMRR ≥ 50dB
CMRR
A_VOL
V_O
I_SC
I_OUT
PSRR
I_S
Common Mode Rejection Ratio
Large Signal Voltage Gain
Output Swing
High
Output Swing
Low
Output Short Circuit Current
Output Current
Power Supply Rejection Ratio
Supply Current (per channel)
V_CM Stepped from 0V to 5V
V_CM Stepped from 0V to 3.8V
V_O = 1.5V to 3.5V
R_L = 1k to V⁺/2
R_L = 10k to V⁺/2
R_L = 1k to V⁺/2
R_L = 10k to V⁺/2
Sourcing to V^−
V_ID = 200mV ^{(7) (8)}
Sinking to V⁺
V_ID = −200mV ⁽⁷⁾⁽⁸⁾
V_OUT = 0.5V From rails
V⁺ = 5V to 6V or V^− = 0V to −1V
Normal Operation
Shutdown Mode (LMH6647 only)
−0.5
−0.3
−0.1
V
5.3
5.5
5.1
56
82
dB
66
85
76
85
74
dB
4.80
4.95
V
4.98
50
200
mV
20
55
mA
53
±20
mA
75
95
dB
700
1400
μA
10
50
(7) Short circuit test is a momentary test.
(8) Output short circuit duration is infinite for V_S < 6V at room temperature and below. For V_S > 6V, allowable short circuit duration is 1.5ms.
±5V Electrical Characteristics
Unless otherwise specified, all limits guaranteed for at T_J = 25°C, V⁺ = 5V, V^− = −5V, V_CM = V_O = 0V, R_f = 2kΩ, and R_L = 1kΩ
to GND. Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
(1)
(2)
(1)
BW
e_n
i_n
CT Rej.
SR
T_ON
T_OFF
TH_SD
I_SD
V_OS
TC V_OS
−3dB BW
Input-Referred Voltage Noise
Input-Referred Current Noise
Cross-Talk Rejection
(LMH6646 only)
Slew Rate
Turn-On Time (LMH6647 only)
Turn-Off Time (LMH6647 only)
Shutdown Threshold
(LMH6647 only)
Shutdown Pin Input Current
(LMH6647 only)
Input Offset Voltage
Input Offset Average Drift
A_V = +1, V_OUT = 200mV_PP
f = 100kHz
f = 1kHz
f = 100kHz
f = 1kHz
f = 5MHz, Receiver:
R_f = R_g = 510Ω, A_V = +2
A_V = −1, V_O = 2V_PP(3)
I_S ≤ 50μA
See ⁽⁴⁾
−5V ≤ V_CM ≤ 5V
See ⁽⁵⁾
40
55
17
25
0.75
1.20
MHz
nV/√Hz
pA/√Hz
47
dB
15
22
V/μs
200
ns
700
ns
4.25
4.60
V
−20
μA
−3
−4
±1
±5
3
4
mV
μV/°C
(1) All limits are guaranteed by testing or statistical analysis.
(2) Typical values represent the most likely parametric norm.
(3) Slew rate is the average of the rising and falling slew rates.
(4) Positive current corresponds to current flowing into the device.
(5) Offset voltage average drift determined by dividing the change in V_OS at temperature extremes into the total temperature change.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMH6645 LMH6646 LMH6647