LMC6492 Datasheet, PDF (5/18 Pages) National Semiconductor (TI) – CMOS Rail-to-Rail Input and Output Operational Amplifier

AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T_J = 25˚C, V⁺ = 5V, V^− = 0V, V_CM = V_O = V⁺/2 and R_L > 1 MΩ. Bold-
face limits apply at the temperature extremes
Symbol
Parameter
Conditions
SR
Slew Rate
(Note 9)
GBW
φ_m
G_m
e_n
i_n
T.H.D.
Gain-Bandwidth Product
Phase Margin
Gain Margin
Amp-to-Amp Isolation
Input-Referred
Voltage Noise
Input-Referred
Current Noise
Total Harmonic
Distortion
V⁺ = 15V
(Note 10)
F = 1 kHz
V_CM = 1V
F = 1 kHz
F = 1 kHz, A_V = −2
R_L = 10 kΩ, V_O = −4.1 V_PP
F = 10 kHz, A_V = −2
R_L = 10 kΩ, V_O = 8.5 V_PP
V⁺ = 10V
Typ
(Note 5)
1.3
1.5
50
15
150
37
0.06
0.01
0.01
LMC6492AE
LMC6494AE
Limit
(Note 6)
0.7
0.5
LMC6492BE
LMC6494BE
Limit
(Note 6)
0.7
0.5
Units
Vµs min
MHz
Deg
dB
dB
%
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-
tended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human body model, 1.5 kΩ in series with 100 pF.
Note 3: Applies to both single-supply and split-supply operation. Continuous short operation at elevated ambient temperature can result in exceeding the maximum
allowed junction temperature at 150˚C. Output currents in excess of ±30 mA over long term may adversely affect reliability.
Note 4: The maximum power dissipation is a function of T_J(max), θ_JA and T_A. The maximum allowable power dissipation at any ambient temperature is P_D = (T_J(max)
− T_A)/θ_JA. All numbers apply for packages soldered directly into a PC board.
Note 5: Typical Values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: V⁺ = 15V, V_CM = 7.5V and R_L connected to 7.5V. For Sourcing tests, 7.5V ≤ V_O ≤ 11.5V. For Sinking tests, 3.5V ≤ V_O ≤ 7.5V.
Note 8: Do not short circuit output to V⁺, when V⁺ is greater than 13V or reliability will be adversely affected.
Note 9: V⁺ = 15V. Connected as voltage follower with 10V step input. Number specified is the slower of the positive and negative slew rates.
Note 10: Input referred, V⁺ = 15V and R_L = 100 kΩ connected to 7.5V. Each amp excited in turn with 1 kHz to produce V_O = 12 V_PP.
Note 11: Guaranteed limits are dictated by tester limits and not device performance. Actual performance is reflected in the typical value.
Typical Performance Characteristics V_S = +15V, Single Supply, T_A = 25˚C unless otherwise
specified
Supply Current vs
Supply Voltage
Input Current vs
Temperature
Sourcing Current vs
Output Voltage
DS012049-25
DS012049-26
5
DS012049-27
www.national.com