LMC567 Datasheet, PDF (2/7 Pages) National Semiconductor (TI) – Low Power Tone Decoder

Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Voltage, Pin 3
Supply Voltage, Pin 4
Output Voltage, Pin 8
Voltage at All Other Pins
Output Current, Pin 8
Package Dissipation
Operating Temperature Range (T_A)
2 V_p–p
10V
13V
Vs to Gnd
30 mA
500 mW
−25˚C to +125˚C
Storage Temperature Range
−55˚C to +150˚C
Soldering Information
Dual-In-Line Package
Soldering (10 sec.)
260˚C
Small Outline Package
Vapor Phase (60 sec.)
215˚C
Infrared (15 sec.)
220˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
Electrical Characteristics
Test Circuit, T_A = 25˚C, V_s = 5V, RtCt #2, Sw. 1 Pos. 0, and no input, unless otherwise noted.
Symbol
Parameter
Conditions
I4
Power Supply
Current
V3
Input D.C. Bias
RtCt #1, Quiescent
or Activated
V_s = 2V
V_s = 5V
V_s = 9V
R3
Input Resistance
I8
Output Leakage
f₀
Center Frequency,
RtCt #2, Measure Oscillator
F_osc ÷ 2
Frequency and Divide by 2
∆f₀
Center Frequency
Shift with Supply
V_s = 2V
V_s = 5V
V_s = 9V
Min Typ Max
0.3
0.5 0.8
0.8 1.3
0
40
1 100
98
92 103 113
105
1.0 2.0
Units
mAdc
mVdc
kΩ
nAdc
kHz
%/V
V_in
Input Threshold
∆V_in
Input Hysteresis
V8
Output ’Sat’ Voltage
L.D.B.W. Largest Detection
Bandwidth
∆BW
Bandwidth Skew
Set Input Frequency Equal to f₀
Measured Above, Increase Input Level
Until Pin 8 Goes Low.
Starting at Input Threshold, Decrease Input
Level Until Pin 8 goes High.
Input Level > Threshold
Choose RL for Specified I8
Measure F_osc with Sw. 1 in
Pos. 0, 1, and 2;
V_s = 2V
V_s = 5V
V_s = 9V
I8 = 2 mA
I8 = 20 mA
V_s = 2V
V_s = 5V
V_s = 9V
11 20 27
17 30 45 mVrms
45
1.5
mVrms
0.06 0.15
Vdc
0.7
7 11 15
11 14 17
%
15
0 ±1.0
%
f_max
Highest Center
Freq.
RtCt #3, Measure Oscillator Frequency and Divide by 2
700
kHz
V_in
Input Threshold at
Set Input Frequency Equal to f_max measured Above,
f_max
Increase Input Level Until Pin 8 goes Low.
35
mVrms
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func-
tional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guar-
antee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is
given, however, the typical value is a good indication of device performance.
www.national.com
2