THS4511 Datasheet, PDF (17/35 Pages) Texas Instruments – WIDEBAND, LOW NOISE, LOW DISTORTION FULLY DIFFERENTIAL AMPLIFIER

THS4511
www.ti.com
SLOS471E – SEPTEMBER 2005 – REVISED NOVEMBER 2009
TEST CIRCUITS
The THS4511 is tested with the following test circuits
built on the evaluation module (EVM). For simplicity,
the power-supply decoupling is not shown—see
Layout in the Application Information section for
recommendations. Depending on the test conditions,
component values are changed per the following
tables, or as otherwise noted. The signal generators
used are ac-coupled 50-Ω sources, and a 0.22-µF
capacitor and 49.9-Ω resistor to ground are inserted
across R_IT on the alternate input to balance the
circuit.
Table 1. Gain Component Values
GAIN
0 dB
6 dB
R_F
348 Ω
348 Ω
R_G
340 Ω
165 Ω
R_IT
56.2 Ω
61.9 Ω
Note the gain setting includes 50-Ω source
impedance. Components are chosen to achieve
gain and 50-Ω input termination.
Table 2. Load Component Values
R_L
100 Ω
200 Ω
499 Ω
1 kΩ
R_O
25 Ω
86.6 Ω
237 Ω
487 Ω
R_OT
Open
69.8 Ω
56.2 Ω
52.3 Ω
ATTEN.
6 dB
16.8 dB
25.5 dB
31.8 dB
Note the total load includes 50-Ω termination by
the test equipment. Components are chosen to
achieve load and 50-Ω line termination through a
1:1 transformer.
Due to the voltage divider on the output formed by
the load component values, the amplifier output is
attenuated. The column Atten in Table 2 shows the
attenuation expected from the resistor divider. When
using a transformer at the output as shown in
Figure 39, the signal will see slightly more loss, and
these numbers will be approximate.
Frequency Response
The circuit shown in Figure 38 is used to measure the
frequency response of the circuit.
A network analyzer is used as the signal source and
as the measurement device. The output impedance
of the network analyzer is 50 Ω. R_IT and R_G are
chosen to impedance match to 50 Ω, and to maintain
the proper gain. To balance the amplifier, a 0.22-µF
capacitor and 49.9-Ω resistor to ground are inserted
across R_IT on the alternate input.
The output is probed using a high-impedance
differential probe across the 100-Ω resistor. The gain
is referred to the amplifier output by adding back the
6-dB loss due to the voltage divider on the output.
From ^VIN
50 W
Source
RG
R_IT
0.22 mF
49.9 W
RG
R_IT
R_F
5V
THS4511
CM
R_F
49.9 W
49.9 W ^{100 W}
Open
0.22 mF
Output Measured
Here With High
Impedance
Differential Probe
Figure 38. Frequency Response Test Circuit
Distortion and 1-dB Compression
The circuit shown in Figure 39 is used to measure
harmonic distortion, intermodulation distortion, and
1-db compression point of the amplifier.
A signal generator is used as the signal source and
the output is measured with a spectrum analyzer. The
output impedance of the signal generator is 50 Ω. R_IT
and R_G are chosen to impedance-match to 50 Ω, and
to maintain the proper gain. To balance the amplifier,
a 0.22-µF capacitor and 49.9-Ω resistor to ground are
inserted across R_IT on the alternate input.
A low-pass filter is inserted in series with the input to
reduce harmonics generated at the signal source.
The level of the fundamental is measured, then a
high-pass filter is inserted at the output to reduce the
fundamental so that it does not generate distortion in
the input of the spectrum analyzer.
The transformer used in the output to convert the
signal from differential to single ended is an
ADT1-1WT. It limits the frequency response of the
circuit so that measurements cannot be made below
approximately 1 MHz.
From ^VIN
50 W
Source
R_G
R_IT
0.22 mF
49.9 W
R_G
R_IT
R_F
5V
THS4511
CM
R_F
R_O
1:1 ^VOUT To 50 W
Test
R_O
R_OT
Equipment
Open
0.22 mF
Figure 39. Distortion Test Circuit
The 1-dB compression point is measured with a
spectrum analyzer with 50-Ω double termination or
100-Ω termination as shown in Table 2. The input
power is increased until the output is 1 dB lower than
expected. The number reported in the table data is
the power delivered to the spectrum analyzer input.
Add 3 dB to refer to the amplifier output.
Copyright © 2005–2009, Texas Instruments Incorporated
Product Folder Link(s): THS4511
Submit Documentation Feedback
17