TL082CMX Datasheet, PDF (1/3 Pages) National Semiconductor (TI) – Engineering Project Manager

Company
National Semiconductor
URL for Additional Information
http://www.national.com/quality/green/
Contact
Gloria Gordon
Title
Engineering Project Manager
Phone
1-408-721-8435
Email
[e-mail]
Part Number
TL082CMX
MSL Rating
1
Peak Body Temp C
235
MaxTime (Sec)
30
Cycles
4
Document Date Contains Lead(Pb) and is NOT European RoHS Compliant. Weight (mg)
Unit Type
29-Dec-2007
NOT China RoHS Compliant
70.000 Each
Homogeneous Material Composition Declaration for Electronic Products
Item
Plastic
Weight (mg) Component
44.710 SiO2
Epoxy Resin
Sb2O3
Brominated Epoxy
CAS#
60676-86-0
25928-94-3
1309-64-4
40039-93-8
Weight (mg)
36.215
7.243
0.894
0.358
Item-ppm
810,000
162,000
20,000
8,000
Part-ppm
517,359
103,472
12,774
5,110
Leadframe
20.560 Cu
Fe
7440-50-8
7439-89-6
20.036
0.493
974,500
24,000
286,225
7,049
Zn
7440-66-6
0.025
1,200
352
Chip
P
2.360 Si
7723-14-0
7440-21-3
0.006
2.346
300
994,000
88
33,512
Ext. LeadFinish
Al
1.840 Sn
7429-90-5
7440-31-5
0.014
1.564
6,000
850,000
202
22,343
Pb
7439-92-1
0.276
150,000
3,943
Die Attach
0.270 Ag
Epoxy Resin
7440-22-4
25928-94-3
0.203
0.068
750,000
250,000
2,893
964
Int. LeadFinish
0.180 Ag
7440-22-4
0.180
1,000,000
2,571
W ires
0.080 Au
7440-57-5
0.080
1,000,000
1,143
Note: The device content disclosed herewith is approximate and is based on engineering estimates only. It has not been verified through analytical testing.
Additionally, the following should be noted:
1. One or more dopant materials may be present in the silicon die at sub-ppm levels to provide semiconductor properties.
2. Epoxy resin components listed are generic and may or may not be the specific compound used, which is considered proprietary.
RoHS Material Composition Declaration
RoHS Directive
2002/95/EC
RoHS Definition: Quantity limit of 0.1% by mass (1000 PPM) in homogeneous material for: Lead (Pb), Mercury, Hexavalent
Chromium, Polybrominated Biphenyls (PBB), Polybrominated Diphenyl Ethers (PBDE) and quantity limit of 0.01% by mass
(100 PPM) of homogeneous material for Cadmium
Subject to the limitations below, National Semiconductor Corporation (“National”) certifies the following information as of the document date.
1. National products with lead-free solder comply with the European Union’s Directive on the Restriction of the Use of Hazardous Substances
2002/95/EC (“RoHS”). These products do not contain homogeneous materials with Joint Industry Guide (JIG) -101 Level A materials above Level A
threshold levels, except lead in RoHS exempt applications 5, 7a and 7c.
2. National products with lead-containing solder do not comply with RoHS, because they contain lead in a non-exempt application. These products do
not contain other RoHS restricted substances or homogeneous materials with JIG-101 Level A materials above Level A threshold levels, except lead in
solder and RoHS exempt applications 5, 7a and 7c.
3. National products are manufactured in conformance with National specifications (SC) CSP-9-111C1 Supplier Environmental Requirements for
Materials and Products and (SC) CSP-9-111S2 National’s List of Banned and Reportable Substances, which are available at
www.national.com/quality/green/.
4. National products do not contain and are not manufactured with ozone depleting substances subject to The Montreal Protocol on Substances that
Deplete the Ozone Layer and U.S. Clean Air Act, Title VI.
National has taken commercially reasonable steps to provide representative and accurate information but may not have independently verified information
provided by others or conducted testing or chemical analysis on incoming materials and chemicals. Information provided in this document is derived from
default values associated with internal process information and may not be representative of all or actual materials used in the product (e.g. the default
may indicate a particular material, while an equivalent compliant material from the same or alternate supplier was actually used). Material concentrations
are the maximum expected concentration of the substances in the device and may not represent the actual concentration. National and National suppliers
consider certain limited information to be confidential and thus CAS numbers and other limited information may not be available for release. National’s
standard warranty and limitation of liability provisions of National’s Standard Terms and Conditions of Sale apply to any issues arising out of or in
connection with the information provided herein unless otherwise provided by a written contract signed by both parties.
NATIONAL ACCEPTS NO DUTY TO NOTIFY USERS OF THIS DECLARATION OF UPDATES OR CHANGES TO THIS DECLARATION.
Gerry Fields
Vice President Quality
National Semiconductor
Page 1 of 3