N08L163WC2C Datasheet, PDF (3/9 Pages) NanoAmp Solutions, Inc. – 8Mb Ultra-Low Power Asynchronous CMOS SRAM 512K × 16 bit

NanoAmp Solutions, Inc.
N08L163WC2C
Advance Information
Absolute Maximum Ratings
Item
Voltage on any pin relative to V_SS
Voltage on V_CC Supply Relative to V_SS
Power Dissipation
Storage Temperature
Operating Temperature
Soldering Temperature and Time
Symbol
V_IN,OUT
V_CC
P_D
T_STG
T_A
T_SOLDER
Rating
–0.3 to V_CC+0.3
–0.3 to 4.5
500
–65 to 150
-40 to +85
260^oC, 10sec
Unit
V
V
mW
o_C
o_C
o_C
Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional oper-
ation of the device at these or any other conditions above those indicated in the operating section of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Symbol
Test Conditions
Min. _Typ¹ Max Unit
Supply Voltage
Data Retention Voltage
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
Read/Write Operating Supply Current
@ 1 µs Cycle Time²
Read/Write Operating Supply Current
@ fmax
Maximum Standby Current
Maximum Data Retention Current
V_CC
2.2 3.0 3.6 V
V_DR
Chip Disabled
1.5
V
V_IH
Vcc = 2.2V to 2.7V
Vcc = 2.7V to 3.6V
1.8
V_CC+0.3
V
2.2
V_CC+0.3
Vcc = 2.2V to 2.7V
–0.3
0.6
V_IL
Vcc = 2.7V to 3.6V
–0.3
V
0.8
V_OH
I_OH = -0.1mA, Vcc = 2.2V
2.0
I_OH = -1.0mA, Vcc = 2.7V
2.4
V
V_OL
I_OL = 0.1mA, Vcc = 2.2V
I_OL = 2.1mA, Vcc = 2.7V
0.4
V
0.4
I_LI
V_IN = 0 to V_CC
-1
1 µA
I_LO
OE = V_IH or Chip Disabled
-1
1 µA
I_CC1
V_CC=3.6 V, V_IN=V_IH or V_IL
Chip Enabled, I_OUT = 0
-L
1.5
3
mA
1.5
3
I_CC2
V_CC=3.6 V, V_IN=V_IH or V_IL Chip
Enabled, I_OUT = 0
-L
12.0 20.0
mA
12.0 15.0
V_IN = V_CC or 0V
I_SB1
Chip Disabled
t_A= 85^oC, V_CC = 3.6 V
-L
2.0 20
µA
2.0
8
I_DR
Vcc = 1.5V, CE ≥ Vcc - 0.2V,
VIN ≥ Vcc - 0.2V or VIN ≤ 0.2V _-L
10
µA
4
1. Typical values are measured at Vcc=Vcc Typ., T_A=25°C and not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
Stock No. 23380-C
3
The specifications of this device are subject to change without notice. For latest documentation see http://www.nanoamp.com.