SP2-DC3V Datasheet, PDF (5/6 Pages) Nais(Matsushita Electric Works) – 15A (2C), 10A (4C) COMPACT POWER RELAYS WITH HIGH SENSITIVITY

SP
Mounting and removal of fastening bracket
1. Mounting
from the groove in the socket, while press-
Insert the A part of the fastening bracket ing with the tip of a minus screwdriver.
into the mounting groove of the socket,
While the bracket is in this position, keep
and then fit the B part into groove, while pressing the C part of the bracket to the
pressing with the tip of a minus screwdriv- relay side with your finger, and lift up to
er.
the left side and remove from the groove,
2. Removal
as in the diagram at right.
Slide the B part of the fastening bracket
Minus screwdriver
C
B
Fastening
bracket
SP relay
A
Terminal block
Screw terminal socket
40.64±0.4
1.600±.016
20.32±0.4
.800±.016
23±1 19.5±0.6
.906±.039 .768±.024
4.5±0.4
.177±.016
30±0.6
1.181±.024
67±1
2.638±.039
15.24±0.4
.600±.016
6.5±0.4
.256±.016
97±1
3.819±.039
40.64±0.4
1.600±.016
20.32±0.4
.800±.016
23±1
.906±.039
70.5±1
2.776±.039
30.48±0.4
1.200±.016
15.24±0.4
.600±.016
32±0.6
1.260±.024
19.5±0.6
.768±.024
6.5±0.3
.256±.012
mm inch
30±0.6
1.181±.024
4.5±0.3
.177±.012
52±1
2.047±.039
11±0.4
.433±.016
40.5±0.6
1.594±.024
21±0.4
.827±.016
52±1
2.047±.039
Mounting hole drilling diagram
30±0.2
1.181±.008
2-DIA. HOLES 4.5±0.1
2-DIA. HOLES .177±.004
Notes:
(1) Mounting screws and the fastening
bracket are included in the package.
(2) Mount the relay with the proper mount-
ing direction — i.e. with the direction of the
NAIS mark on top of the relay case match-
ing the direction of the NAIS mark on the
terminal block. (The ; direction of the
terminal block is the upward direction of
the relay.)
Fastening bracket mounting and
removal
1. Mounting
Insert the A part of the fastening bracket
into the mounting groove of the terminal
block, and then fit the B part into groove,
while pressing with the tip of a minus
screwdriver.
2. Removal
Slide the B part of the fastening bracket
from the groove in the terminal block,
while pressing with the tip of a minus
screwdriver. While the bracket is in this
position, keep pressing the C part of the
bracket to the relay side with your finger,
Mounting plate
and lift up to the left side and remove from
the groove, as in the diagram at right.
Minus screwdriver
C
B
Fastening
bracket
SP relay
A
Terminal block
18.4
25
.724
.984
57.2
2.252
SP-MA
23.2
.913
The SP-Relay with
SP-MA attached
18.4
2-DIA. HOLES 3.2
.724
2-DIA. HOLES .126
Panel cutout
Tolerance: ±0.1 ±.004
Direct chassis mounting possible,
and applicable to DIN rail.
[DIN 46277 (35 mm width) is applicable.]
256