LSN-T10-D12J Datasheet, PDF (3/12 Pages) Murata Manufacturing Co., Ltd. – Single Adjustable Output, Non-isolated, 12Vin, 10A, SIP, DC/DC Converters

LSN-T/10-D12
Single Adjustable Output, Non-isolated, 12Vin, 10A, SIP, DC/DC Converters
Performance/Functional Specifications
Typical @ TA = +25°C under nominal line voltage, VOUT=5V, and full-load conditions unless noted.
Input
Input Voltage Range
10-14 Volts (12V nominal)
Input Current:
Normal Operating Conditions
Inrush Transient
Standby/Off Mode
Output Short-Circuit Condition
See Ordering Guide
0.02A²sec
5mA
60mA average
Input Reflected Ripple Current
30mAp-p
Input Filter Type
Capacitive
Overvoltage Protection
None
Reverse-Polarity Protection
None
Start-up Voltage
9.2 Volts
Undervoltage Shutdown
8 Volts
On/Off Control
Positive Polarity (no suffix)
Negative Polarity
On = Pin open to +VIN max.
Off = Zero (ground) to +0.8V max.
On = Pin open or grounded to +0.3V
Off = +2.5V to +VIN max.
On/Off Current
0.5 mA maximum
Output
Maximum Output Power
51 Watts
VOUT Accuracy (50% load)
Minimum Loading
±2%
No minimum load
Maximum Capacitive Load
2,000μF (ESR < 0.02 Ohms)
10,000μF (ESR > 0.02 Ohms)
VOUT Trim Range
Ripple/Noise (20MHz BW)
+0.7525 to +5.5 Volts (no load)
See Ordering Guide
Extreme Accuracy
3% max. over line/load/temperature
Efficiency
See Ordering Guide
Pre-Bias Startup
Converter will start up if the external output
voltage is less than Vsetpoint
Overcurrent Detection and Short-Circuit Protection:
Current-Limit Inception
Cold Condition
21 Amps
Short-Circuit Detection Point
98% of VOUT set
SC Protection Technique
Hiccup with auto recovery
Short-Circuit Current
400mA average
Dynamic Characteristics
Transient Response (50-100-50% load) 50μsec to ±2% of final value
Start-Up Time:
VIN to VOUT and On/Off to VOUT
Switching Frequency:
8msec
250 ±30 KHz
Environmental
Calculated MTBF
TBC
Operating Temperature: (Ambient)
Without Derating (Natural convection) –40 to +85°C
With Derating
See Derating Curves
Storage Temperature
-40 to +125°C
Thermal Shutdown
+115°C
Physical
Dimensions
See Mechanical Specifications
Pin Dimensions/Material
0.03" (0.76mm) dia. round copper with
tin plate over nickel underplate.
Length: 0.17” (4.32mm)
Weight
0.3 ounces (8.5g)
Flamability Rating
UL94V-0
Absolute Maximum Ratings
Input Voltage:
Continuous or transient
On/Off Control (Pin 11)
Input Reverse-Polarity Protection
Output Overvoltage Protection
Output Current
Storage Temperature
Lead Temperature (soldering, 10 sec.)
14 Volts
+VIN
None
None
Current limited. Devices can
withstand sustained output short
circuits without damage.
–40 to +125°C
+280°C
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in
the Performance/Functional Specifications Table is not implied.
All models are tested and specified with external 22μF tantalum input and 10 || 1μF output
capacitors.These capacitors are necessary to accommodate our test equipment and may not
be required to achieve specified performance in your applications. All models are stable and
regulate within spec under no-load conditions.
See Technical Notes and Performance Curves for details.
The On/Off Control (pin 11) is designed to be driven with open-collector logic or the appli-
cation of appropriate voltages (referenced to Common, pins 5 and 6).
Output noise may be further reduced with the installation of additional external output
filtering. See I/O Filtering and Noise Reduction.
MTBF’s are calculated using Telcordia SR-332(Bellcore), ground fixed, TA = +25°C, full
power, natural convection.
Do not exceed maximum rated output power when adjusting the output voltage.
www.murata-ps.com
Technical enquiries email: [e-mail], tel: [phone]
LSN-T10-D12.B01 Page 3 of 12