MVAC400-12AFR Datasheet, PDF (7/8 Pages) Murata Power Solutions Inc. – 400W 3 x 5 High Density AC-DC Power Supply Converter

MVAC400 Series
400W 3" x 5" High Density AC-DC Power Supply Converter
MECHANICAL DIMENSIONS – MVAC400-xxAF and MVAC400-xxAFD
& 
> @
& 
> @
07*
“
“
$ 
> @
07*
7%
-
3,1
3,1
5(029('
“
“ ^{% }
-
3,1
> @
“
“
07*
35,0$5<
+($76,1.
127( _!
07*
02817,1*6/276
:,'7+  
> @
0$;6&5(:+($'
',$0(7(5 
6(&21'$5<
+($76,1.
127( _!
MOUNTING GRID
A
B
4.50 x 2.50 114.30 [4.500] 63.50 [ 2.500]
4.55 x 2.55 115.57 [4.550] 64.77 [ 2.550]
&
>@
>@
-
3,1
-
3,1
-
3,1
-
3,1
J2
6 12
5 11
4 10
39
28
17
J3
21
43
65
87
1-6
+DC_OUT
7-12 +DC_OUT_RTN
1
+5V_AUX
2
PWR_OK
3
+12V_FAN_RTN
4
PS_ON
5 +REMOTE_SENSE
6 -REMOTE_SENSE
7
+12V_FAN
8
+5V_AUX_RTN
$//',0(16,216$5(,100>,1@
“
“
SAFETY CONSIDERATION NOTES:
1. Protective bonding conductor from the end product protective earthing terminal must be tied to TB1. For optimum EMI performance, while maintaining
Class I safety isolation all 4 mounting holes must be tied to the end product protective earthing terminal. To maintain Class II safety isolation mounting
holes MTG1 and MTG2 need to be isolated from protective earth and should use standoffs of non-conductive material.
2. This power supply requires mounting standoffs of minimum 6mm in height. If there is risk of chassis deformation or shorter standoff height isrequired,
an appropriate insulator must be used under the power supply with adequate extension beyond the outline of the power supply. In all cases,the
applicable safety standards must be applied to ensure proper creepage and clearance requirements are met.
3. The primary heatsink is considered a live primary circuit, and should not be touched. It is recommended that the primary heatsink be kept at least
3.5mm from chassis and 7mm from secondary circuits. In all cases, the applicable safety standards must be applied to ensure proper creepage and
clearance requirements are met.
4. This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to:
http://www.murata-ps.com/requirements/
5. Used only in non-tropical conditions.
6. Double pole/neutral fusing.
Dimensions: 3.0" x 5.0" x 1.4" (76.2mm x 127mm x 35.6mm)
INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS – MVAC400-xxAF and MVAC400-xxAFD
Connector
PIN
Description
Mating Housing
Crimp terminal/pins
Input Connector J1: 1
Molex 26-62-4030 3
AC Neutral
AC Line
Molex 0009930300
Molex 0008500105 (18-24 AWG)
Molex 0008500107 (22-26 AWG)
Output Connector J2: 1,2,3,4,5,6
Molex 39-28-1123 7,8,9,10,11,12
+DC_OUT
+DC_OUT_RTN
Molex 0039012125
Molex 0039000038
1
+5V_AUX
2
PWR_OK
3
+12V_FAN_RTN
Output Connector J3: 4
Molex 90130-1108 5
PS_ON
+Remote Sense
Molex 0901420008
Molex 0901190109
6
-Remote Sense
7
+12V_FAN
8
+5V_AUX_RTN
www.murata-ps.com/support
MVAC400.B02 Page 7 of 8