MSK738B Datasheet, PDF (2/5 Pages) M.S. Kennedy Corporation – INVERTING OPERATIONAL AMPLIFIER

ABSOLUTE MAXIMUM RATINGS
±VCC
IOUT
VIN
TC
Supply Voltage +18V ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Peak Output Current
○
○
○
○
○
○
○
○
○
○ ±200mA
Differential Input Voltage ○ ○ ○ ○ ○ ○ ○ ○ ○ ±12V
Case Operating Temperature Range
(MSK 738B/E)
-55°C to+125°C
○
○
○
○
○
○
○
○
(MSK 738) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +85°C
TST Storage Temperature Range ○ ○ -65°C to +150°C
TLD Lead Temperature Range ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 300°C
(10 Seconds Soldering)
PD Power Dissipation ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ See Curve
TJ Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 150°C
ELECTRICAL SPECIFICATIONS
±Vcc=±15V Unless Otherwise Specified
Parameter
Test Conditions
Group A
MSK 738B/E
Subgroup Min. Typ. Max.
MSK 738
Min. Typ. Max.
Units
STATIC
Supply Voltage Range 2
-
±12 ±15 ±18 ±12 ±15 ±18 V
Quiescent Current
VIN=0V
1
- ±39 ±40 - ±39 ±42 mA
AV=-1V/V
2,3
- ±40 ±42 -
-
-
mA
Thermal Resistance ²
Junction to Case Output Devices
-
-
46
-
-
46
-
°C/W
INPUT
Input Offset Voltage
Bal. Pins=NC VIN=0V AV=-100V/V
1
- ±25 ±75 - ±50 ±100 µV
Input Offset Voltage Drift ²
VIN=0V
2,3
- ±0.5 ±1
-
-
- µV/°C
Input Offset Adjust
RPOT=10KΩ To+VCC AV=-1V/V
1
Adjust to zero
Adjust to zero
mV
2,3
Adjust to zero
-
-
-
mV
Input Bias Current 7
VCM=0V
1
- ±10 ±40 - ±20 ±60 nA
Either Input
2,3
- ±20 ±80 -
-
-
nA
Input Offset Current
VCM=0V
1
-
2
20
-
10
30
nA
2,3
-
5
40
-
-
-
nA
Input Impedance 2
F=DC Differential
-
-
5
-
-
5
-
MΩ
Power Supply Rejection Ratio 2
∆VCC=±5V
-
-
1
10
-
2
20 µV/V
Input Noise Voltage 2
F= 0.1Hz To 10Hz
-
- 0.15 -
-
0.2
-
µVp-p
Input Noise Voltage Density 2
F=1KHz
-
- 3.8
-
-
4
- nV√Hz
Input Noise Current Density 2
F=1KHz
-
- 0.6
-
-
0.7
- pA√Hz
OUTPUT
Output Voltage Swing
RL=100Ω AV=-3V/V F≤20MHz
4
±10 ±12
-
±10 ±11.8 -
V
Output Current
AV=-3V/V TJ<150°C
4 ±100 ±120 - ±100 ±120 -
mA
Settling Time 1 2
0.1% 10V step
4
-
30
40
-
35
45
nS
Full Power Bandwidth
RL=100Ω Vo=±10V
4
20 22
-
15 20
-
MHz
Bandwidth (Small Signal) 2
RL=100Ω
4
175 200
-
165 190
-
MHz
TRANSFER CHARACTERISTICS
Slew Rate
VOUT=±10V RL=100Ω Av=-1.5V/V
Open Loop Voltage Gain 2 RL=1KΩ F=1KHz VOUT=±10V
4
3200 3500 - 3500 3200 -
4
100 110
-
95 105 -
V/µS
dB
NOTES:
1 AV= -1, measured in false summing junction circuit.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.
4 Military grade devices ("B" suffix) shall be 100% tested to subgroups 1,2,3 and 4.
5 ^{Subgroups 5 and 6 testing available upon request.}
6 ^{Subgroup 1,4 TA=TC=+25°C}
Subgroup 2,5 TA=TC=+125°C
Subgroup 3,6 TA=TC=-55°C
7 Measurement taken 0.5 seconds after application of power using automatic test equipment.
2
Rev. B 6/03