MSK5102-50_15 Datasheet, PDF (2/6 Pages) M.S. Kennedy Corporation – Extremely Compact 10 Pin Flatpack With Metal Base

ABSOLUTE MAXIMUM RATINGS ⁹
VINP VIN Pulse (100mS max,1% Duty)
VIN Input Voltage
VEN Enable Voltage
IOUT Output Current
-20V to +60V
26V
-0.3V to 26V
3.5A
TST Storage Temperature Range
TLD Lead Temperature
(10 Seconds Soldering)
TJ Operating Temperature
MSK5102 Series
MSK5102H Series
-65°C to +150°C
300°C
-40°C to +85°C
-55°C to +125°C
ELECTRICAL SPECIFICATIONS
Parameter
Output Voltage Tolerance
Dropout Voltage 2
Load Regulation 8
Line Regulation
Output Current Limit 2
Ground Current 2
Output Noise 2
Enable Input Voltage 2
Enable Input Current 2
Shutdown Output Current 2
Thermal Resistance 2
Thermal Shutdown
Test Conditions 1 3
Group A ^{MSK5102H SERIES}
MSK 5102 SERIES
Subgroup Min. Typ. Max. Min. Typ. Max.
IOUT=10mA; VIN=VOUT+1V
1
-
±0.5 ±1.0 -
±0.5 ±1.0
2,3
-
±1.0 ±2.0 -
-
-
∆VOUT=-1%; IOUT=100m A
1
-
80
200 -
80
225
∆VOUT=-1%; IOUT=1.5A
1
-
350 600 -
350 625
VIN=VOUT+1V
1
-
±0.2 ±1.0 -
±0.2 ±1.2
10mA ≤ IOUT ≤ 1.25A
2,3
-
±0.3 ±2.0 -
±0.3
-
(VOUT +1V) ≤ VIN ≤ 26V
1
-
±0.05 ±0.5 -
±0.05 ±0.6
IOUT=10mA
2,3
-
±0.5 ±1.0 -
±0.5
-
VOUT=0V; VIN=VOUT+1V
-
-
2.1
3.5 -
2.1
3.5
VIN=VOUT+1V; IOUT=0.75A
-
-
18
30 -
18
30
VIN=VOUT+1V; IOUT=1.5A
-
-
32
-
-
32
-
CL=10µF; 10Hz ≤ f ≤ 100KHz
-
-
400
-
-
400
-
HIGH/ON
1
2.4
-
- 2.4
-
-
LOW/OFF 1
-
-
0.8 -
-
0.8
HIGH/ON
1
-
100 600 -
100 600
LOW/OFF 1
-
-
2
-
-
2
VENABLE ≤ 0.8V
-
-
10
500 -
10
500
Junction to Case @ 125°C
-
-
5.6
6
-
5.6
7
TJ
-
-
135
-
-
135
-
Units
%
%
mV
mV
%
%
%
%
A
mA
mA
µV
V
V
µA
µA
µA
°C/W
°C
NOTES:
1 Output decoupled to ground using 10µF minimum capacitor unless otherwise specified.
2 This parameter is guaranteed by design but need not be tested.
Typical parameters are representative of actual device performance but are for reference only.
3 All output parameters are tested using a low duty cycle pulse to maintain TJ = TC.
4 Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.
5 Military grade devices ('H' suffix) shall be 100% tested to subgroups 1,2,3 and 4.
6 Subgroup 1,4 TC=+25°C
Subgroup 2
TJ=+125°C
Subgroup 3
TA=-55°C
7 Please consult factory if alternate output voltages are desired.
8 Due to current limit, maximum output current may not be available at all values of VIN-VOUT and temperatures. See typical perfor-
mance curves for clarification.
9 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
2
8548-36 Rev. D 5/15