MSK4204RH_15 Datasheet, PDF (2/6 Pages) M.S. Kennedy Corporation – Total Dose Hardened To TBD Krad(Si) (Method 1019.8 Condition A)

ABSOLUTE MAXIMUM RATINGS ⁸
V+ High Voltage Supply ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 100V
V Logic Supply 20V CC
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
IOUT Continuous Output Current ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○10A
IPK Peak Output Current
20A
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
VOUT Output Voltage Range
GND-5V min. to V+ max.
V Input Voltage Vcc IN
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
VL Logic Input Voltage (Shutdown) ○ ○ ○ ○ ○ ○ 0V to Vcc
V High-Side Bias 20V B
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TST Storage Temperature Range ○ ○ ○ ○ -65°C to +150°C
TLD Lead Temperature Range ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 300°C
(10 Seconds)
TC Case Operating Temperature
MSK 4204 K/H RH ○ ○ ○ ○ ○ ○ ○ ○ ○ -55°C to +125°C
MSK 4204 RH ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +85°C
TJ Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○+150°C
θJc Thermal Resistance
(Output FETS @ 125°C) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2.5°C/W
(Ouput Diodes @ 125°C) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○3.2°C/W
ELECTRICAL SPECIFICATIONS
NOTES:
1 VCC=15V, V+=28V, AV-,BV-=Ground, Shutdown=OV unless otherwise specified.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial grade devices shall be tested to Subgroups 1, 4 and 7 unless otherwise requested.
4 Military and Space grade devices ("H" and "K") shall be 100% tested to subgroups 1,2,3,4,5,6 and 7.
5 Subgroup 1,4,7 TA=TC= +25°C
2,5
TA=TC= +125°C
3,6
TA=TC= -55°C
6 Industrial grade and devices shall be 100% tested at 25°C only.
7 The internal on resistance is for the die only. This should be used for thermal calculations only.
8 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
9 Pre and post irradiation limits @ 25°C, up to TBD Krad, are identical unless otherwise specified.
2
PRELIMINARY Rev. B 1/11