G100E_14 Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – G100E Series

Model Selection Guide
www.micropowerdirect.com
Input
Model
Number
Voltage (VDC)
Current (mA)
Voltage
Nominal Range Full-Load No-Load ^(VDC)
G101E
5
4.5 - 5.5
286
30
5.0
G102E
5
4.5 - 5.5
256
30
9.0
G103E
5
4.5 - 5.5
256
30
12.0
G104E
5
4.5 - 5.5
250
30
15.0
G105E
5
4.5 - 5.5
278
30
±5.0
G106E
5
4.5 - 5.5
260
30
±9.0
G107E
5
4.5 - 5.5
253
30
±12.0
G108E
5
4.5 - 5.5
250
30
±15.0
G111E
12 10.8 - 13.2 117
15
5.0
G112E
12 10.8 - 13.2 109
15
9.0
G113E
12 10.8 - 13.2 107
15
12.0
G114E
12 10.8 - 13.2 105
15
15.0
G115E
12 10.8 - 13.2 116
15
±5.0
G116E
12 10.8 - 13.2 107
15
±9.0
G117E
12 10.8 - 13.2 105
15
±12.0
G118E
12 10.8 - 13.2 107
15
±15.0
G121E
24 21.6 - 26.4 57
8
5.0
G122E
24 21.6 - 26.4 53
8
9.0
G123E
24 21.6 - 26.4 53
8
12.0
G124E
24 21.6 - 26.4 52
8
15.0
G125E
24 21.6 - 26.4 57
8
±5.0
G126E
24 21.6 - 26.4 52
8
±9.0
G127E
24 21.6 - 26.4 52
8
±12.0
G128E
24 21.6 - 26.4 52
8
±15.0
Other input/output combinations are available
(i.e. 3.3 VDC). Contact the factory for details at:
[e-mail]
Output
Current
(mA, Max)
Current
(mA, Min)
Load
Regulation
(%, Max)
200.0
20.0
15
111.0
12.0
15
83.0
9.0
15
67.0
7.0
15
±100.0
±10.0
15
±56.0
±6.0
15
±42.0
±5.0
15
±33.0
±4.0
15
200.0
20.0
15
111.0
12.0
15
83.0
9.0
15
67.0
7.0
15
±100.0
±10.0
15
±56.0
±6.0
15
±42.0
±5.0
15
±33.0
±4.0
15
200.0
20.0
15
111.0
12.0
15
83.0
9.0
15
67.0
7.0
15
±100.0
±10.0
15
±56.0
±6.0
15
±42.0
±5.0
15
±33.0
±4.0
15
Derating Curve
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
70
500
78
500
78
500
80
500
72
500
77
500
79
500
80
500
71
200
76
200
78
200
79
200
72
200
78
200
79
200
78
200
73
100
78
100
78
100
79
100
73
100
79
100
80
100
80
100
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load. Operation at no-load
may cause damage to the unit.
3. These converters will operate without external components. However, when measuring output
ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the
-Vout pin for single output
units and from each out-
put to common for dual
output units. An input
Vin
Input
Capacitor
Vout
Output Capacitor
Single Dual
capacitor will enhance 5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF
stability over temperature
and input line variations.
Recommended capacitor
values are given in the
12 VDC
24 VDC
2.2 µF
1.0 µF
9 VDC 4.7 µF 2.2 µF
12 VDC 2.2 µF 1.0 µF
15 VDC 1.0 µF 0.47 µF
table above. For applica-
tions requiring very low output noise levels, a simple LC filter should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this,
connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output
common.
5. It is recommended that a fuse be used on the input of a power supply for protection. See the
Model Selection table above for the correct rating.
Mechanical Dimensions
Pin Connections
Pin Single Dual
Pin Single
1 -Vin -Vin
7 NC
NC
8 -Vout Common
NC = No Connection
9 +Vout
11 No Pin
14 +Vin
Dual
+Vout
-Vout
+Vin
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the top of the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]